USED Gas Engine

Good Used BEHR German fan clutch replacement for 113,111, 108 and 109 chassis gas engines from 1968 to 1973, all 114 and 115 gas and diesel, all 123 gas and diesel engines 1977 to 1983 and 1981 to 1983 126 300SD. PLEASE NOTE: This clutch is for engines that have the 5 blade aluminum metal fans. If you have the newer multi-blade nylon fan then you will need a different type. This clutch lists new for $272.00. If your fan clutch is loose, making noise, or your engine is overheating this is your chance to replace it for a very good price. We also carry these new for $178.00

I have aluminum fan blades used if you need that also. Email for price.

PLEASE NOTE: This will not fit 107, 116, or 126 V8 gas engines.

Excellent suspension air compressor and PS pump from a 1965 300SE. Pump has been inspected, cleaned and tested.

I believe this came off my 189 engine but am not sure. Please review picture closely. Some slight pitting but no major rust through. 

Good clean straight lower transmission cover as shown

Small gear for 189 engine as shown. Minimal teeth wear.

Set of hardware and cover as shown.

Good used set of original connecting rods from 1965 189 engine

Good straight camshaft oiler tube for 189 engine

From 1965 189 Engine as shown. Application / location unknown.

Good used rocker arm assemblies from a 1965 189 engine that was installed in a 300SE coupe. May bit other years and models of 189 engine.  

Good used complete set of Bosch Fuel Injection Trigger points for 4.5 V8 from 1973 to 1976.  Does not fit 108 or 109 3.5 or 4.5

Good used exhaust header bracket as shown for 189 engine.

Good used braided and hard fuel line assembly as shown for 189 engine.

Good used 189 engine lift bracket as shown. 

189 Adjusting bracket as shown.

Cast Iron 189 Engine Bracket as shown.  Not sure of exact application

189 engine part as shown. Do not know exact application or years.

Complete part and bracket as shown for 189 engine. Operational electric solenoid.

Part shipped as shown. Linkage, levers, bracket and idle stabilizer removed from a 1965 189 engine that was installed in a 300SE coupe. 

Good used regulator from a 1965 189 engine that was installed in a 300SE coupe. 

Good used metal heat shield as shown for 189 engine

Excellent used short section exhaust manifold removed from a 1965 189 engine that was installed in a 300SE coupe. This is an above average manifold with minimal surface rust and good flange and crack free bolt holes. Cast part number is 189 142 04 02

Excellent used long section exhaust manifold removed from a 1965 189 engine that was installed in a 300SE coupe. This is an above average manifold with minimal surface rust and good flange and crack free bolt holes. Part number on the manifold casting is 189 142 03 02

Good used set of metal fuel injector lines from a 1965 189 engine that was installed in a 300SE coupe. These will fit engines with the 6 element fuel injection pump.

Good used 189 engine coolant intake manifold. This unit is made out of aluminum and is prone to corrode right next to the through bolts.  If you have a 189 300SE you had better have one of these around for a spare. These are a real problem part on these engines. 

Good used generator mounting plate and mounting strap as shown. Removed from later model 189 engine. 

Excellent used fan clutch and pulley with mount as shown. Removed from a 1965 300SE 189 engine that was in the process of being restored. Should fit all later 189 engines with this type of engine fan unit. 

Good used cylinder head from late model 189 engine with 6 element injection pump. Removed from a 1965 300SE. No major corrosion in and around water passages and good valve seat areas.

Good used flywheel from a 1965 189 engine that was installed in a 300SE coupe with manual shift transmission. Good clutch face and excellent gear teeth. 

Good used timing chain tensioner from a 1965 189 engine that was installed in a 300SE coupe.