116

Excellent used working turbo diesel starter motor. Fits all turbo diesel from 1978 to 1985. Can be used on 240D and 300D non turbo engines to get them to start faster. No modification required.

You have asked for it and we have delivered again. Now that all those old power steering pumps are leaking out the front seal we have come up with a kit that will allow you to replace the front seal of your pump at home without any special tools. This kit will work on all power steering pumps on 4 and 5 cylinder diesel engines from 1977 to 1985 (excluding the 190D 2.2).

Kit contains the following:

IMPORTANT NOTE: We do not sell replacement antenna masts by year and model. We have run across too many problems with confusion, interchangeability, and previously swapped antennas. We sell a SMOOTH TAIL mast and a TOOTHED TAIL mast. Smooth tails were used on most of the power Hirschmann antennas up to the early 80's and tooth tails were used on the later masts. For you to order the proper one you must partially remove your current mast and inspect. Is the white plastic tail more or less smooth or does it have teeth in it? The one describe here is the TOOTHED style.

CLICK HERE to view the smooth style.

Brand new Genuine OEM silver wheel center cap. Make those wheels look beautiful again! Fits all 14 inch alloys on 107 116 114 115 123 and 126 chassis
to 1985 with the bundtcake style wheels. If you need more than one, just change your quantity in the cart!

Good used speaker switch as shown.

Good used lug wrench as shown. Some plating has worn off with minor pitting. For 14 inch alloy wheels with 17 mm lug bolts.

This is the tool I love to use when troubleshooting engine operating temperature problems. You can stand back and aim the beam right on a spot on the radiator or engine to get an exact temperature reading. This can indicate whether or not your radiator is plugged and confirm if your temperature gauge is accurate or not.

If you are running SVO it can give you accurate readings of the temperature of your oil - both during filtering and coming out of your boost heater.

Features:

Good Used BEHR German fan clutch replacement for 113,111, 108 and 109 chassis gas engines from 1968 to 1973, all 114 and 115 gas and diesel, all 123 gas and diesel engines 1977 to 1983 and 1981 to 1983 126 300SD. PLEASE NOTE: This clutch is for engines that have the 5 blade aluminum metal fans. If you have the newer multi-blade nylon fan then you will need a different type. This clutch lists new for $272.00. If your fan clutch is loose, making noise, or your engine is overheating this is your chance to replace it for a very good price. We also carry these new for $178.00

I have aluminum fan blades used if you need that also. Email for price.

PLEASE NOTE: This will not fit 107, 116, or 126 V8 gas engines.

Set of FIVE Rebuilt Bosch Fuel Injector Housings with high performance Monark Nozzles installed. Each injector has been bench tested and pressure balanced in our shop. All injectors are set to release pressures between 1900 and 1950 psi. This set of injectors will work in all 300SD 1978 to 1985 and all 123 300D 300CD and 300TD with turbo diesel engines.

Injectors will be shipped with new heat shield washers as shown. No instructions included.

NO CORE CHARGE / NO CORE RETURN

In working on many 61x series diesel engines, I have often found one or more of these clamps missing. Missing or loose clamps is the number one reason for injector hard line crack failure. There should be a clamp like this between each two hard lines to minimize vibration fatigue failure. 2 used clamps are included with correct bolts and nuts.

This lug wrench came with most models from the mid 60s to the late 70's that used the standard hubcaps. The end has a curved tip to allow you to pry the hubcap off.

Excellent used oil pump assembly for 617 turbo diesel engines. Pump has been taken apart and inspected for scoring and teeth wear. No adverse wear noted - above average condition

Good used emergency brake cable lever located inside rear brake rotor. Fits all models from chassis in title.

Good used emergency brake shoe adjuster star nut and pin. Fits all models from chassis in title.

Are you weary of the sluggish performance and maintenance hassles of your current SVO WVO Conversion? We are now offering  the two key components of our own STC kits as a performance upgrade to non-Mercedessource conversions. These two key components can be installed to work with any other conversion. From our experience these will give you smoother starts, more horsepower, better fuel economy, longer filter life, and greatly ease the hassles associated with air in the fuel system during filter changes or other periodic maintenance.

Front suspension overhaul is almost always left until one has fixed everything else on the car. We know that most owners can live with some looseness in the suspension, especially when you consider the age of the 116 chassis. But if you want to restore that great Mercedes factory feel and ride (that we all love!) there is no short cut but to replace all the rubber and wear parts in the lower section of your front suspension. NOTE: This kit does not include the upper control arms as we have found many have already replaced those as they often fail first. If yours have not been replaced and you want the full deal, then we recommend you also order those separately. CLICK HERE.

Good used complete set of Bosch Fuel Injection Trigger points for 4.5 V8 from 1973 to 1976.  Does not fit 108 or 109 3.5 or 4.5

Fits all these chassis from 1968 to 1985. For drain bolt on automatic transmission torque converter. For a complete transmission flush the torque converter must be drained separately. Good to have a new aluminum sealing washer on hand during the service. 

High Quality (made in USA) brass two way fuel rated valve with brass fittings for 3/8 inch fuel hose. Can be used to select between two fuel tanks or as a control valve for your loop or return fuel with running on SVO. Comes with two straight non-barbed hose fittings and one 90 degree fitting. This will allow max flexibility in how you route your fuel hoses. NO instructions included.

High Quality (made in USA) brass two way fuel rated valve with brass fittings for 8 mm or 5/16 inch fuel hose. Can be used to select between two fuel tanks or as a control valve for your loop or return fuel with running on SVO. Comes with two straight non-barbed hose fittings and one 90 degree fitting. This will allow max flexibility in how you route your fuel hoses. NO instructions included.

NEW LOCTITE PRODUCT - AUGUST PROMO! If you have read very many of my manuals and instructions you already know how much I detest Silicone Gasket Sealant. I know there are places for silicone (ie bath tub caulking, etc), but it should not be used on internal combustion engines!

FITS THE FOLLOWING: 108, 109, 114, 115, 107, 116, 123, and 126 (up to 1985). Fits all sedans and coupes from these chassis 1965 to 1985. Includes one Genuine OEM Mercedes front rubber seal. No instructions included.

Please note: You only need to open the  sunroof to change this seal. It can be a little tricky to get the new seal in the groove. No instructions included with this seal. It is intended for those who have already done the job. If you need instructions then I recommend you purchase our complete seal kit.

FITS THE FOLLOWING: 108, 109, 114, 115, 107, 116, 123, and 126 (up to 1985). Fits all sedans and coupes from these chassis 1965 to 1985. Includes one quality german aftermarket rear rubber seal. No instructions included.

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with  large size hose clamp. Hose clamp size is 32-50/9.

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with 10 medium size hose clamp. Hose clamp size is 16-27/9.

These rubber end plugs can be used to cap off your vacuum on the end of a line or on certain components. FOR USE ON VACUUM SYSTEM ONLY. These are NOT to be used on fuel injectors.

When was the last time you knocked one of your vacuum lines off around the oil filter housing, only to discover when you tried to reattached it that the fittings were swollen and would just not stay connected? This is a L shaped fitting that fits 115, 116, 123, and 126 chassis.

When was the last time you knocked one of your vacuum lines off around the oil filter housing, only to discover when you tried to reattached it that the fittings or hose were swollen and would just not stay connected? Here is some extra vacuum hose to fix your problem. Fits 115, 116, 123, and 126 chassis.

ONE meter cut piece.