115, New Parts Kits and Manuals

This small rubber cap protects dirt from entering your level indicator on your brake fluid reservoir. Fits 107 114 115 116 123 126 201 and 124 models from the early 70s to mid 1990s.

This large size rubber grommet is a common leak area at the bottom of your brake fluid reservoir. Fits all 107 chassis, 114 and 115 chassis, 116 chassis and 123 chassis from 1972 to 1985.

If you are looking for something special to do for your 4 cylinder diesel this Christmas then this is it! If you have been reluctant to replace your worn and inefficient Bosch fuel injector nozzles because the job is too difficult or too costly then think again!

We are going to make it easy for you this Christmas season. When our high performance nozzles are installed and balanced-tuned properly you will not believe the difference it makes in how your diesel engine performs. Here is what one customer recently wrote in to report:

• Type OM 615 - 4 Cylinder Diesel Engine
• Engine spare parts list
• Production date July 1973
• Edition D
• 165 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

I have used a LOT of different kinds of grease in my lifetime - but this is my favorite. It has a high molybdenum and grahite content and does not dry out over time. It also has a great resistance to water and moisture deterioration. Just the right consistency - not too thick so it can get into tight places - not too thin so it stays in place.

On the body I use it in door check straps, window gears and mechanisms, seat tracks, door latch assemblies, sunroof cables and gears, hood and trunk hinges and any other metal to metal wear location. On suspension and chassis I use it on wheel bearings, ball joints, tie rods, u-joints, backing plates and more.

This 14 oz can is usually more than enough to service most Mercedes Benz. A must have in your tool box!

Now in a pak of 25 for even more savings. These are my favorite European hose clamps. They tighten securely, don't cut into the hose, and don't rust or break. If you are working on an SVO  fuel system for any Mercedes I recommend you have these clamps on hand. Cheaps clamps can cuase air leaks leading to great frustration- the US style clamps with holes that cut into the rubber. These clamps will work on all 8 mm hose, 5/16 and 3/8 US spec fuel or coolant hose.

For use with our all fuel specification SUPER FUEL HOSE. CLICK HERE to read more.

New replacement AFTERMARKET window regulator and motor assembly. This does not look the same as your original but will fix and may even work better than factory. (not as easily bent). And the price is right. Will fit 115 chassis sedans ONLY.

If you are going to buy or have just purchased an older 4 cylinder Mercedes Diesel the first thing you need to do is a good physical exam of the engine. It is even better to do this BEFORE you purchase the car to prevent surprises and pain in your wallet. Check out what happened to us recently in our PROJECT DRIVEWAY restoration project by CLICKING HERE!

FITS THE FOLLOWING: all 107, 108, 109, 111, 113, 114, 115, 116, 123 and 126 chassis from 1969 to 1991. Four pads included for both sides of rear axle. Tired of sqweeking or squealing or hard brake pedal feel? These are just amazing brake pads. Manufactured by Meyle in Germany these have high quality anti-squeal plates built into the back side of each pad and are scorched at the factory for more driving comfort. What does scorched mean? Let  me explain:

Description: High Quality all steel coolant-based heat exchanger. Professionally made for Mercedes Benz back in the 1980’s. New Old Stock from Mercedes Dealer. We only have a few available. Highly efficient and compact with no thermostat control.  Unit is covered by thick foam insulation tube. Measures approximately 10 inches long and 2 1/2 inches in diameter. Coolant hose connections are for 5/8  ID hose. Fuel connections are for either 5/16 (8 mm) or 3/8 inch fuel hose. NOTE: you can use 3/8 inch fuel hose by leaving the plastic cover on the nipple and just cutting off the end of the plastic cap. Ruler is for reference only and is not included.

Description: High Quality all steel coolant-based heat exchanger. Professionally made for Mercedes Benz back in the 1980’s. New Old Stock from Mercedes Dealer. We only have a few available. Highly efficient and compact with no thermostat control.  Unit is covered by thick foam insulation tube. Measures approximately 10 inches long and 2 1/2 inches in diameter. Coolant hose connections are for 5/8  ID hose. Fuel connections are for either 5/16 (8 mm) or 3/8 inch fuel hose. NOTE: you can use 3/8 inch fuel hose by leaving the plastic cover on the nipple and just cutting off the end of the plastic cap. Ruler is for reference only and is not included.

I have gone through a lot of pain dealing with leaks in SVO conversion systems. Vegetable oil has an amazing wicking ability and will leak out of the slightest thread flaw. This is particularly true if you use iron pipe fittings or fittings of dissimilar metals.

Fits all Mercedes Diesels that use the 90 degree fuel prefilter. This prefilter is made by Hebmueller of Germany and is excellent quality. It has brass inserts in the ends so they cannot collapse or crack when the fuel hose clamps are tightened down. Now sold individually! If you want more than one, just change your quantity in the shopping cart. We also sell these in a six pack for a better price break.

Diesel purge is amazing stuff! It is getting so popular that we have decided to offer it on the website individually, so now you can buy per can. This injection cleaner is run directly through the fuel system in the engine compartment. It is not a fuel tank additive. Does not include instructions or bypass hose. If you want more than one can just change your quantity in the shopping cart.

Lubro Moly Diesel hi test fuel additive. Formulated for the new low sulfur diesel fuel. Contains an additive against injection pump and injector wear. Keeps the injection system clean. Provides clean, low smoke combustion. Regular use guarantees lowest exhaust emission levels. If you are running petrol diesel it is a must to be using a fuel additive in the older Mercedes diesels. Sold per can, treats 20 gallons.

These are the zip ties we have all been looking for. They have a super sticky tape of the foot of the tie so you can stick them anywhere in your engine compartment without having to drill a hole in the inner fender panel. (NOTE: Be sure to thoroughly clean the surface BEFORE installing). The other neat thing is that these zip ties can be loosened back up (just like the factory type) to remove the wire bundle or anything else you need to secure. Sold in packs of 6. You will love these!

This new shift knob fits all 4 speed diesel transmissions from 1969 to 1983. It is a german aftermarket replacement that is made out of hard plastic rather than rubber, so it will not deteriorate like the original style. Good quality at a good price!

This is the tool I love to use when troubleshooting engine operating temperature problems. You can stand back and aim the beam right on a spot on the radiator or engine to get an exact temperature reading. This can indicate whether or not your radiator is plugged and confirm if your temperature gauge is accurate or not.

If you are running SVO it can give you accurate readings of the temperature of your oil - both during filtering and coming out of your boost heater.

Features:

If you want Monark Nozzles that are tuned and balanced and don't want to rebuild them yourself we can sell you a set of FIVE Rebuilt Bosch Fuel Injector Housings with high performance Monark Nozzles installed. Each injector has been bench tested and pressure balanced in our shop. All injectors are set to release pressures between 1600 and 1650 psi. This set of injectors will work in all 300D 300CD from 1975 to 1981 and all 300TD from 1978 to 1980, NON Turbo ONLY!.

Injectors will be shipped with new heat shield washers as shown. No instructions included.

If you want Monark Nozzles that are tuned and balanced and don't want to rebuild them yourself we can sell you a set of four Rebuilt Bosch Fuel Injector Housings with these high performance Nozzles installed. Each injector and been bench tested and pressure balanced in our shop. All injectors are set to release pressures between 1600 and 1650 psi. This set of injectors will work in all 220D and 240D from 1969 to 1983 as well as 190D 2.2 (1984 and 1985).

Injectors will be shipped with new heat shield washers as shown. No instructions included.

Fits all these chassis from 1968 to 1985. For drain bolt on automatic transmission torque converter. For a complete transmission flush the torque converter must be drained separately. Good to have a new aluminum sealing washer on hand during the service. 

High Quality (made in USA) brass two way fuel rated valve with brass fittings for 3/8 inch fuel hose. Can be used to select between two fuel tanks or as a control valve for your loop or return fuel with running on SVO. Comes with two straight non-barbed hose fittings and one 90 degree fitting. This will allow max flexibility in how you route your fuel hoses. NO instructions included.

High Quality (made in USA) brass two way fuel rated valve with brass fittings for 8 mm or 5/16 inch fuel hose. Can be used to select between two fuel tanks or as a control valve for your loop or return fuel with running on SVO. Comes with two straight non-barbed hose fittings and one 90 degree fitting. This will allow max flexibility in how you route your fuel hoses. NO instructions included.

If you have read very many of my manuals and instructions you already know how much I detest Silicone Gasket Sealant. I know there are places for silicone (ie bath tub caulking, etc), but it should not be used on internal combustion engines!

FITS THE FOLLOWING: 108, 109, 114, 115, 107, 116, 123, and 126 (up to 1985). Fits all sedans and coupes from these chassis 1965 to 1985. Includes one Genuine OEM Mercedes front rubber seal. No instructions included.

Please note: You only need to open the  sunroof to change this seal. It can be a little tricky to get the new seal in the groove. No instructions included with this seal. It is intended for those who have already done the job. If you need instructions then I recommend you purchase our complete seal kit.

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with  large size hose clamp. Hose clamp size is 32-50/9.