110/111/112 Sedan, New Parts Kits and Manuals

If you are looking for something special to do for your 4 cylinder diesel this Christmas then this is it! If you have been reluctant to replace your worn and inefficient Bosch fuel injector nozzles because the job is too difficult or too costly then think again!

We are going to make it easy for you this Christmas season. When our high performance nozzles are installed and balanced-tuned properly you will not believe the difference it makes in how your diesel engine performs. Here is what one customer recently wrote in to report:

• Type OM 621 - 4 Cylinder Diesel Engine
• Engine spare parts list
• Production date December 1966
• Edition B
• 172 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

• Type M 115 - 4 Cylinder Gas Engine
• Engine spare parts list
• Production date May 1971
• Edition C
• 202 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

• Type M 189 - 6 Cylinder Gasoline Fuel Injected Performance Engine
• Engine spare parts list
• production date January 1969
• Edition C
• 174 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

• Type M 129 - 6 cylinder fuel Injected Engine
• Engine spare parts list
• Production date January 1967
• Edition B
• 116 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

• Type M 108 - 6 Cylinder Carburator Engine
• Engine spare parts list
• Production date November 1968
• Edition B
• 104 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

• Type M 114 V - 6 cylinder Gas
• Carburetor Engine
• Engine spare parts list
• Edition B
• Production date October 1970
• 120 pages

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

• Type M121 - 4 CYLINDER GAS ENGINE
• Engine Spare Parts List
• Edition D
• 222 Pages 

COVERS ALL ENGINE PARTS WITH MERCEDES PARTS NUMBERS. GOOD USED CLEAN ORIGINAL CONDITION

I have used a LOT of different kinds of grease in my lifetime - but this is my favorite. It has a high molybdenum and grahite content and does not dry out over time. It also has a great resistance to water and moisture deterioration. Just the right consistency - not too thick so it can get into tight places - not too thin so it stays in place.

On the body I use it in door check straps, window gears and mechanisms, seat tracks, door latch assemblies, sunroof cables and gears, hood and trunk hinges and any other metal to metal wear location. On suspension and chassis I use it on wheel bearings, ball joints, tie rods, u-joints, backing plates and more.

This 14 oz can is usually more than enough to service most Mercedes Benz. A must have in your tool box!

Now in a pak of 25 for even more savings. These are my favorite European hose clamps. They tighten securely, don't cut into the hose, and don't rust or break. If you are working on an SVO  fuel system for any Mercedes I recommend you have these clamps on hand. Cheaps clamps can cuase air leaks leading to great frustration- the US style clamps with holes that cut into the rubber. These clamps will work on all 8 mm hose, 5/16 and 3/8 US spec fuel or coolant hose.

For use with our all fuel specification SUPER FUEL HOSE. CLICK HERE to read more.

Description: High Quality all steel coolant-based heat exchanger. Professionally made for Mercedes Benz back in the 1980’s. New Old Stock from Mercedes Dealer. We only have a few available. Highly efficient and compact with no thermostat control.  Unit is covered by thick foam insulation tube. Measures approximately 10 inches long and 2 1/2 inches in diameter. Coolant hose connections are for 5/8  ID hose. Fuel connections are for either 5/16 (8 mm) or 3/8 inch fuel hose. NOTE: you can use 3/8 inch fuel hose by leaving the plastic cover on the nipple and just cutting off the end of the plastic cap. Ruler is for reference only and is not included.

Description: High Quality all steel coolant-based heat exchanger. Professionally made for Mercedes Benz back in the 1980’s. New Old Stock from Mercedes Dealer. We only have a few available. Highly efficient and compact with no thermostat control.  Unit is covered by thick foam insulation tube. Measures approximately 10 inches long and 2 1/2 inches in diameter. Coolant hose connections are for 5/8  ID hose. Fuel connections are for either 5/16 (8 mm) or 3/8 inch fuel hose. NOTE: you can use 3/8 inch fuel hose by leaving the plastic cover on the nipple and just cutting off the end of the plastic cap. Ruler is for reference only and is not included.

This is a must have for any owner of an older Mercedes gas engine model. This applies to all 4, 6 and 8 cylinder from the mid 1950s to the mid 1980s. The manual covers prevention of thread damage and how to repair a totally destroyed spark plug hole. The thread chaser included with the manual with help clean up any minor damage and prevent major problems. Never force a spark plug into the threads and if a plug comes out hard the threads MUST be cleaned with a chaser before you reinstall a new plug.

These are the zip ties we have all been looking for. They have a super sticky tape of the foot of the tie so you can stick them anywhere in your engine compartment without having to drill a hole in the inner fender panel. (NOTE: Be sure to thoroughly clean the surface BEFORE installing). The other neat thing is that these zip ties can be loosened back up (just like the factory type) to remove the wire bundle or anything else you need to secure. Sold in packs of 6. You will love these!

This is the tool I love to use when troubleshooting engine operating temperature problems. You can stand back and aim the beam right on a spot on the radiator or engine to get an exact temperature reading. This can indicate whether or not your radiator is plugged and confirm if your temperature gauge is accurate or not.

If you are running SVO it can give you accurate readings of the temperature of your oil - both during filtering and coming out of your boost heater.

Features:

If you have read very many of my manuals and instructions you already know how much I detest Silicone Gasket Sealant. I know there are places for silicone (ie bath tub caulking, etc), but it should not be used on internal combustion engines!

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with  large size hose clamp. Hose clamp size is 32-50/9.

Applies to all Mercedes, PON FIN Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126, 201, and 124 chassis. Here is a kit you will love to have around the shop. If you don't like using those poor quality US hose clamps (the kind that cut into the hose) then here is a chance to have spare quality (no nick) hose clamps for those fuel and coolant related repairs. Kit comes with 10 medium size hose clamp. Hose clamp size is 16-27/9.

Great to carry in trunk for emergencies. Nice case. No instructions included with this kit. Bulbs are applicable to most models from the early 70's to late 80's.

This kit includes:

Running badly means poor performance. It happens sooner or later to EVERY diesel owner. The word "performance" is often used to describe how well a diesel engine runs once started. The principles discussed will cover all Mercedes diesels from the mid 1950s to the mid 1990s. Throughout this manual I will use this word to discuss a number of common problems. How performance is rated can mean different things to different people. In the following pages I will relate diesel performance to the following four criteria:

• How much power does it produce?
• What kind of fuel economy does it deliver?
• How smooth does the engine run?
• How much does the engine smoke?

These thin shim washers can be added to an existing injector shim to meet the thickness required to increase release pressure. Buy using a thicker shim along with 1 to 3 thin shims you will be able to make a number of different thicknesses within the 0,20 mm range. This kit contains six each of thin 0,20 mm washers.

These thin shim washers can be added to an existing injector shim to meet the thickness required to increase release pressure. Buy using a thicker shim along with 1 to 3 thin shims you will be able to make a number of different thicknesses within the 0,10 mm range. This kit contains six each of super thin 0,10 mm washers

If you are adjusting your injectors and your pressure reading is low you may only have to add one or two of the thin washers to bring the pressure up to spec. If your pressure reading is too high you will need to go down in thickness by choosing a think shim you have available and adding 1 or 2 thin (or any multiple you like) ones to build the thickness required. We also supply thin washer sets in 0,05 and 0,20 mm sizes.

These thin shim washers can be added to an existing injector shim to meet the thickness required to increase release pressure. Buy using a thicker shim along with 1 to 3 thin shims you will be able to make a number of different thicknesses within the 0,05 mm range. This kit contains six each of super thin 0,05 mm washers

If you are adjusting your injectors and your pressure reading is low you may only have to add one or two of the thin washers to bring the pressure up to spec. If your pressure reading is too high you will need to go down in thickness by choosing a think shim you have available and adding 1 or 2 thin (or any multiple you like) ones to build the thickness required. We also supply thin washer sets in 0,10 and 0,20 mm sizes.

Both myself and our customers are so impressed with the quality and performance of Monark Nozzles I wish I could convince everyone to install them in their Mercedes diesel. To tune them properly you will need a bench pressure tester and these adjustment shims. Be sure to click on the links below to see what else you will need to rebuild and tune your fuel injectors.  Kent Bergsma

This bulb is a single element bulb that is used in the brake light, rear turn signal and your rear back up lens. It's a very universal bulb. Fits mid 60s to 90s Mercedes.

This is a 3 piece scribe and pick tool set - great for marking aluminum and steel.

Heat shrink tubing is very handing to have if you are doing any wire connections or splicing. This tubing can go over the splice or solder joint and when heat is applied from a heat gun it will shrink right down tight to the joint and protect it from shorts and corrosion.

This circuit tester has a long 7 inch point to get into hard to reach places. Accordion cord extends up to 12 feet! Wow!

This is a set of metric nut drivers. It come in 7 different handy sizes and is even color coded. Sizes include 5, 6, 7, 8, 9, 10, and 11mm.