Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
Quality German oil filter quantity of 2. For 450, 380, 500, 420, and 560 engines.
Easy to replace. You do not need to get under the car. Access to the lid is on the right side of these engines just below the forward section of the valve cover.
This right angle screwdriver is great for working in tight places - like removing speakers, voltage regulators, distributor caps, etc.
January 2019 notice: This filter is now available only in very limited quantities and may not be readily available in the future. This is why we are not able to include it in our full fluid flush kit ( See related products below) This is an often neglected filter.
High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.
These are the plastic bushings that hold fuel injectors into the head of the late M116 and M117 engines. These get very brittle with age. If you are planning on removing your fuel injectors I highly recommend you order these to have on hand.
This is a very common failure item on the older gas models. The braided outlet fuel hose will rot and and begin by weeping fuel through the hose. When it finally fails it can be dangerous and leave you stranded on the road. Large amounts of fuel will come pouring out of the tank.
This check valve is mounted on the end of the electric fuel pump and prevents pressure from bleeding off after the engine has shut down. If you engine is slow to start after it has sat overnight that could be a sign the check valve needs replacement.
New timing chain tensioner and gasket.
Another High Quality product from Lubro Moly. This is a 300ml can of Motor Oil Saver. It Rejuvenates rubber and plastic engine seals and reduces oil consumption via the piston rings and valve guides; counteracts the loss in viscosity of motor oils.
Brand new thermostat, heavy-duty short hose, and 2 new clamps. Fits all 126 Chassis 380 engines from 1981 to 1985 both in 107 chassis and 126 Chassis. Free Video installation tips included ( click on the arrow in the center of the picture to watch below:
This item can only be shipped UPS Ground because it is a liquid. One Liter of correct Power steering fluid. Fully compatible with Dexron II systems but has enhanced aditives to reduce steering box gear wear.
New rubber stop for rear exhaust bracket. It plugs into the body right above the back of the rear muffler. Helps prevent rattle. Fits almost all models from late 1960s to mid 1990s. When you hear something clunking in the back when you go over a bump, this part is probably missing.
Applies to 111 113 108 109 107 114 116 126 Chassis Mercedes.
This size freeze plug fits almost all gas and diesel engines from the early 70s up into the 90s. This includes all 61x and 60x diesel engines, the 103 gas engine in the 190E, 300SE and 300E. It also fits many V8 engines but you should measure your current plug to be sure.
If you plan to change coolant hoses this is a must-have labor-saving tool. This is one cleverly designed tool. I could not have done it better myself. I actually use to make a couple of different types before I found this one.
Almost all Mercedes gas and diesel engines from the late 50's up to the early '90s used pressed in steel pins to hold the timing chain guide rails in position (inside the engine block).
New Bremi distributor rotor fits models listed above from 1986 to 1991. Check yours now for heavy burn marks or arcing.
New Bosch distributor cap fits models listed above from 1986 to 1991. Check yours now for cracks or arching.
Fits all GAS ENGINE exhaust systems for W107, W116, W126, W124 and W201 chassis from 1972 to 1995. Gas engine exhaust systems are generally heavier and run hotter than diesel engine exhaust systems. This is a wider and more heavily reinforced exhaust hangar than the standard round type.
Replace your old worn and weak expansion tank cap to eliminate minor coolant loss problems. Watch the video below as Kent will explain the difference in caps and why you want to make sure you purchase the correct one.
This "permanent" red threadlocker is probably the best that I have used. It has the best sealing cap and cures rapidly and reliably when confined between metal parts. Use it to lock threaded fasteners, nuts, bolts and screws from loosening.
FITS THE FOLLOWING: All models PON, FIN, P55, 110, 111, 112, 113, 108, 109, 114, 115, 107, 116, 123, 124, 126, and 201 chassis. Here is my all time favorite gasket maker and sealant. You may already know how I feel about RTV silicone products (I think they should be outlawed!).
Fits all W116, W123, and W126 Turbo Diesel 5 cylinder 300D and 300SD engines from 1981 -1985 as well as M110 6 cylinder engines from 1977 to 1985. This is a brand new Lower engine Oil Pan and Gasket. Remove and inspect your oil pan if it has been badly dented.
Fits all 123 and 126 chassis and later R107 as noted above - both gasoline and diesel models. It may fit a few other models as well but you MUST measure your old hose before ordering. We also carry the 15mm hose for most of the older models. See related products below:
FITS THE FOLLOWING: all 116 300SD from 1978-1980, R107 chassis from 1977 to 1989, 123 chassis both gas and Diesel from 1977-1985 and 126 chassis both Gas and Diesel from 1981 to 1991. Also 124 Chassis 260E 300E 300TD 300D 2.5.
ALERT! ALERT! 10 years after I first started warning about this, I saw it again in my shop on Feb. 20, 2011. Seems to be happening even more now as these radiators age. I loosened up the upper hose clamp on this 123 300TD radiator and it just fell off.
Fits later 107 and 123 as well as 126, 201, and 124 chassis oil caps (black plastic). Tired of having a hard time getting your oil filler cap off without using pliers. Or are you tired of the unsightly oil leaks around the cap. These gaskets can help solve those problems.
Applies to the following chassis: 111, 108, 109, 107, 116 and 126. Includes 3.5, 4.5, 350, 380, 450, 500, 420, and 560 V8 engines from 1970 to 1991. When Mercedes introduced their small 3.5 liter V8 in 1970 it was hailed as a technological breakthrough in automotive engine design.