Good connector with soft rubber. Not cracked. See the picture below to show the location.
In this 15-minute on-demand video, Kent will explain how to use his injection pump de-gunking kits to clean out an old pump and to check the flow rate between each delivery valve. Watch the YouTube short video below to get an overview of these kits.
In this 25-minute, very detailed instructional video, Kent will show you how to use his special tool to remove the guide pins holding the top timing chain guide rails in the cylinder heads.
This is a must-have tool if you own a 1970 to 1991 M116 or M117 V8 engine. It will also work on older six-cylinder gas and four and 5-cylinder engines from the 1960s up through 1985. Note: The included video instructions only cover removal and installation of the pin.
ONLY ONE SET AVAILABLE. Do not order more than one. These are NOT reproductions. These are original NOS fuses from. the 1960s.
In this short 3-minute video, Kent will show you a trick that few know about. You can get those tapered shaft ball joints ( like to find on tie rods and control rods) loose without damaging the rubber boot. It can be faster and less painful than using traditional methods.
If you have one of our pressure brake bleeders, you can easily attach this wand to the end of the hose by removing the brake master cylinder reservoir cap. You can place the exact amount of fluid in the tank, hang the wand in the fill hole, lock the valve open, and walk away.
VERY GOOD used condition. No deformation and the rubber is still soft.
This is the style of fuel pump used.
For all 1968 to 1979 111 coupe, 108, 109, 114, 115, 107C, 116 (included 1980 models(. Do you have a power sunroof that is working poorly or maybe not at all? Does it move slowly in the morning, but it works fine when it heats up during the day?
The power window is stuck closed. Do the tests outlined in this video first. You may have to remove the regulator and to do that; you have to lower the window. But how???
In Kent's 32-minute video on rewiring the plugs on your D-jetronic fuel injectors, he will walk you through the two options on how you can use this kit - then show you how in do it and finally give you some tips on automotive wire splicing using the best tools and supplies.
On most D-jetronic engines, the fuel injector wiring plugs are hard and brittle, and the boots are torn or missing altogether. You may say, "If it is working, why fix it? Watch the videos below to understand why this is important and how easy it would be for you to do it yourself.
In this xx-minute video, Kent will share some tips and tricks to get new side seals installed in your old Benz. We are sorry we are not able to supply side seals at this time, as the aftermarket ones available are lacking in quality.
These old power non-tilting sunroofs are now 45-plus years old. These are specifically the sunroofs that used the early-style rectangular sunroof motor and separate drive mechanism connected by a rubber drive bushing. They did not come with deflector air dams.
This is the FIRST thing you should do on your D-Jet V8 engine. This is true when approaching fixing any older gasoline or diesel engine. If you don't do this, you will be guessing and spending money forever trying to get the engine to run right!
Did the engine just quit? Does it just not start even with prolonged cranking? What could it be? The first thing you want to determine with most older cars is whether there is spark to the plugs.
Very good condition. Has all three pins on the back side intact along with the original spring clips.
Good used 3.5 emblem. This emblem is located on rear of the trunk on the right side of all 280SE, 280SEL, and 300SEL 3.5s produced between 1970 and 1971.
The original fuel filter has a rigid right-angle fitting, as shown in the pictures below. We do not provide this fitting in our fuel delivery kits as more often than not it can be removed from your old filter and installed in the new filter we provide.
PLEASE NOTE: EACH HOLDER HAS SIX SLOTS
When removing valve covers or changing wires, replace these with new ones. They may look good, but they usually break due to engine heat and age.
Kent has been "into" lubrication since his younger years, flying and working on airplanes over 50 years ago.
Testing fuel pressure is a simple procedure on the D-Jetronic engines, but it is ABSOLUTELY essential. If your fuel pressure is off even a few pounds, it will dramatically change the fuel mixture, and your engine will end up running too rich or too lean.
In this 32-minute, very detailed video, Kent will show you how you can fix some heavy rust pitting and small rust-out holes in the trunk of your classic Benz. This technique also works on floors and under body panels.
GENUINE MERCEDES FRONT SUNROOF SEAL
In this video, Kent will show you the tricks of getting the front sunroof seal installed without pulling your hair out. It will require the tool shown that is included with the purchase of the front seal.
In this short video, Kent will demonstrate how to prep the sunroof if there is rust in the seal area and how to install a new rear seal using the tool, lubricant, and glue provided in his kit. PLEASE NOTE: The sunroof panel has to be removed from the car.
For all 108, 109, 114, 115, 116, 123, and 126 (up to 1985) with video instructions
In this 23-minute step-by-step "how-to" video, Kent will show you how to install a new set of fuel injectors in your early D-Jetronic engine. This video is included free with the purchase of our early 3.5 and 4.5 fuel injector sets.
The subjects included are:
These are becoming harder to find in good condition. They were often used as the spare tires in these older models.
If you plan to replace, test, or service your electronic fuel injectors you first must determine which bottom seals you will need. If you have a 1970 or 1973 model, you most likely have the single-bottom seal (unless your engine has been changed).
Kent walks you through replacing a trunk seal on a 1970 280SL. The video is 13 minutes long and covers removing the old seal, cleaning the groove, trial fitting the new seal, and the final gluing procedure.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
Yes, YOU can fully drain all your transmission without using any type of "power flush." Full detailed video instructions are included. This kit is easy to connect and the process is quick and clean. Watch Kent's YouTube video below for full details.
You will receive ten each of the following sizes: 8/12, 10/16, and 12/22. These are much better than U.S. style hose clamps that cut into the hose.
You can not believe how easy it is to move and adjust your old seat after lubrication the tracks with this amazing lubricant! You will receive two full tubes plus the extension nozzle. This is more than enough lube to do the seats with four tracks on each side.
These quality 6.5 inch wire cutters are made of special steel, the blades are high-frequency hardened steel. Suitable for cutting soft copper wire, plastic wire, small cable, aluminum wire, soft alloy wire, jewelry making, multifunctional manual edge banding pliers.
Good used all-metal driver and passenger-side tail light bulb holders for early sedans. The later models were plastic. These are above-average units with bright reflectors and good bulb sockets.
In this 9-minute instructional video, Kent explains how to set up his injection pump cleaning and testing kit ( available separately ), and use it to clean out old fuel injection pumps of gum and grime, and then how to test them to make sure they are delivery fuel through every line.
Watch the videos below to learn about the capabilities of this kit. Kent used it on his 6.3, which had sat outside and had not run in 19 years.
This fits a number of lmid 1960s to early 1970s models with automatic transmission. 250SL 280SL 250S 250SE 280S 280SE 280SE 300SEL. Check under the front of your car to make sure this matches what you have before ordering.
Just so you know, not all parts shown will fit in all years and models of the W108 and W109. This assortment of parts is priced very low. If you are restoring a W108 or W109, there may be some real treasure here for you.
Flushes Out Old Grease and Repacks Bearings with Less Mess. This Handy Packer works on bearings up to 3 1/2" O.D.
Excellent quality zinc plated hose clamps as shown. These can be tighten with a straight blade screw driver or a 7mm socket or nut driver.
Kent is a firm believer in using these strong magnets inside a transmission pan to help extend its useful life.
They should be placed toward the rear of the pan as shown in the picture below.
Many of these, especially along the bottom of the hard are hard and brittle and will break when removing the panel. Tilt and twist to remove and install in the holde. Sold in a bag of 24.
Almost every early SL Kent comes across needs new front wheel bearings. These get so neglected and hardly ever replaced. We are offering a very high quality kit as shown above that will include free grease for your new wheel bearings.
PLEASE NOTE: Since the introduction of this kit in 2019, it has been modified to speed installation and reduce cold. See modified instructions below. You can watch the Youtube video to understand what this kit can do, but attachment to the injection pump has been simplified..
In this 17-minute video instruction, Kent walks you through the steps to install his door liner kit using thick, clear, and high-quality plastic sheets on both front and rear doors. A W123 sedan is shown here, but the principles are similar for other chassis.
If you own an older Mercedes sedan or wagon, it is a very good idea to remove all four door panels, repair components, clean drains, and, most importantly, lubricate all moving parts, as Kent explains in numerous YouTube videos.
