Exhaust Hanger Shock Mount Repair Kit Instructions By Kent Bergsma - Download
The digital PDF instructions will walk you through the install and detailed photos will visually assist you step by step. PDF is 4 pages long.
Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
The digital PDF instructions will walk you through the install and detailed photos will visually assist you step by step. PDF is 4 pages long.
Applies to 190D, 200D, 220D, 240D, 300D, 300CD, 300TD and 300SD (Not for 1984 to 1985 190D) Downloadable PDF eBook 3 explains how to properly remove and replace the glow plugs in the early diesel engines up to 1985.
In a perfect world your diesel would not leak a drop of fluid. Unfortunately, with the age of your vehicle, it may not be economically possible to eliminate every leak. Sometimes you may just have to live with some leaks.
This instruction booklet is meant to be an introduction to simple rust repairs. I have also written a manual that goes into more advanced repairs using Miracle Paint to replace larger rotted sections of sheet metal.
For all 107 chassis SL and SLC models built from 1972 to 1989 and all 114 / 115 chassis sedans and coupes from 1968 to 1976. If the front end of your W107 SL or SLC convertible or coupe or 114/115 wanders on the road or thunks when you go over railroad tracks
This repair guide covers all 114 and 115 chassis Mercedes sedans built from 1968 to 1976. Removing a 114/115 chassis door panel and doing related door maintenance and repair are all fairly easy jobs for the do-it-yourselfer.
Brand new rear end differential front seal. Fits both gas and diesel models. This is NOT the seal for the axles.
Dirko sealing compound is permanently elastic, cold vulcanizing, silicone-rubber based. Can be used for connecting joints, cylinder head, crankcase, oil sump, timing case, thermostat, water pump, transmission, axles, differential, radiator, chassis.
General-purpose, clear RTV indoor/outdoor sealant. Seals, bonds, repairs, mends and secures glass, metal, plastics, fabric, vinyl, weather stripping and vinyl tops. Protects and repairs electrical wiring. May be applied to horizontal or vertical surfaces. Waterproof and flexible.
Sil-Glyde is a silicone based brake lubricant recommended for the entire brake assembly and is compatible with rubber. It is moisture-proof and heat resistant to +600 degrees F, which means it won't burn-off like other brake noise products.
Cold Weld sets up in 15 minutes and has a test proven strength greater than 3000 psi after 16 hours. Resistant to most shop fluids including: water, diesel, fuel, gasoline, antifreeze, hydraulic fluids, motor oil, and transmission fluids. Can be drilled, filed, sanded, machined and painted.
This is a must-have if you have a prized Benz or any car you don't drive often!! If you let any of your cars sit for long periods ( generally over 30 days) without driving them, you can ruin your battery, especially if you let it go completely dead.
Fits all DIESEL ENGINE exhaust systems for 115, 116, 123, 126, 124 and 201 chassis from 1968 to 1995. If you are looking for a more robust exhaust hanger this is it! It is a stronger and more secure exhaust hanger than the standard round rubber type.
This is not a normal nut. On the face it has a special hard plastic nylon seal. When this seal deteriorates you may see evidence of power steering fluid seeping out of the bottom the the adjustment locknut (located on the top of the steering box).
Common wear item. Check for looseness where they nylon bushing sits in the aluminum connector. This is a brand new Shift rod Metal Connector with Nylon Bushing installed. Sold individually. List price $20.00
New ATE Clutch Slave Cylinder. No instructions. No fittings or hoses. If you need to replace one cylinder you should replace both.
New Clutch Master Cylinder. No instructions. No fittings or hoses. If you need to replace one cylinder you should replace both.
New RIGHT FRONT door seal on 4 door sedans only. Only seal shipped. No clips or instructions.
This is a very handy smaller torque wrench to have in your toolbox. Perfect for spark plugs. It will do fuel injectors but is not quite big enough to torque wheel lug bolts. Range is 5 to 80-foot pounds. The case will be black rather than red.
Nice set of pick tools with plastic handles. They have strong steel tips which allow for more prying and twisting with less tendency to bend the tips as you would with dental pick tools. Note: Quarter is not included! Shown for size reference only
This is Kents new favorite ratchet wrench for turning engines over during service and repair. There are a number of maintenance procedures that require you rotate the engine over by hand.
Final drive seal (45 x 65 x 11mm)
Fits Mercedes Benz:
Engine Camshaft Woodruff Key
3 Degrees Offset
Fits Mercedes Benz:
Replace those nuts that keep loosening up with nylock metric nuts that just won't come off. Inside the door panel on the window regulators. Around the engine compartment. Air filter housing nuts. etc. etc.
Excellent used flywheel. Has good gear teeth for starter motor.
If you already have or are willing to buy a 5 pound slide hammer this special threaded fitting will allow you to PULL the pre-chamber from the cylinder head once you have removed the collar nut and the glow plug ( a collar nut removal tool is required look below to learn more).
I have used a lot of different clamping tools over the years to prevent fluids from leaking out when removing coolant, fuel, or brake fluid hoses. Most work ok. Some are hard to use in tight places. Many do not stop every last drip from coming out of the hose.
Fits Mercedes Benz: 230 250 280 250S 280S 280C 220 250C
This set of 5 pick tools have very thin and sharp points. Best set Kent has found to remove orings in hard to get to locations. The variety of angles available allows you to get into almost anywhere to remove and o-ring, sealing ring or other small part.
If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.
Works on 110, 115, 116, 123, 201, 126 and 124 diesel engines 200D 220D 240D 300D 300CD 300TD 300SD 190D 300SDL. We have found that over half of the deep sockets we test will not go over some of the longer injectors.
Maintenance Alert: We have had lots of reports of these bolts loosening up! They WILL shear off if not caught early enough. When that happens the pulley will fall off. At high speed this can lead to engine overhead and even a damaged radiator.
For use on 220 240D 300D 300CD 300TD 300SD 1968 to 1985. NO INSTRUCTIONS INCLUDED: The tool is meant for someone who has the factory manual or who already knows how to adjust their injection pump timing on the older diesel engines. Injection pump timing is critical for peak performance.
Kent originally wrote this manual to go along with our 617 Turbo Diesel Front Crank Seal Replacement Kit as well as our 616 and 617 NON Turbo Crank Seal Kit. We have found that many of you are having problems with your front crank bolt loosening up or bolts sheer
This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.
PLEASE READ CAREFULLY. This line will not fit the 601 602 and 603 diesel engines produced from 1984 to 1995. If you order in error this part is not returnable. See applicable models and years in subtitle. We had this new straight hard line specially manufactured for us in Germany.
This right angle screwdriver is great for working in tight places - like removing speakers, voltage regulators, distributor caps, etc.
Use this special swedge fittings when making any type of copper coil coolant heater for our SVO WVO fuel system. One end of this fitting clamps down tight on the copper pipe and the other end can accept any standard fitting with 1/4 inch male national pipe thread.
Use this special swedge fittings when making any type of copper coil coolant heater for our SVO WVO fuel system. One end of this fitting clamps down tight on the copper pipe and the other end can accept any standard fitting with 1/4 inch male national pipe thread.
This is one of Kent's favorite tools. Lets you reach into tight places - very long nose curved pliers with teeth - like hemostat. With the locking handles it is amazing what this clamp / pliers can hold - and the tight places it can get into!
January 2019 notice: This filter is now available only in very limited quantities and may not be readily available in the future. This is why we are not able to include it in our full fluid flush kit ( See related products below) This is an often neglected filter.
WARNING: IF YOU ORDER THE WRONG ONE IT IS NOT RETURNABLE.
I like the convenience of using the factory jack points (holes) but I absolutely DO NOT like using the factory jack - except in cases of emergency road side repair. You all know it can be a little unstable... I solved this problem by using a large heavy duty bolt.
SPECIAL ORDER PART -- MAY BE UP TO A WEEK BEFORE SHIPPING!
Crushable seal ring that fits between the prechamber and the cylinder head. Genuine first oversize thickness 2.3mm. SOLD INDIVIDUALLY. New seals may be required to repair fuel and air leaks around the top of the prechambers. Special tools are required to replace this seal.
Plastic adjusting knob with clip. Fits many years and models with manually adusting mirrors.
Good used flywheel stretch bolt as shown. Very limited stock. Torque converter flex plate bolts.
UPDATE: This yellow slide hammer is no longer available. You can purchase our new silver Version 4 model. See related products below. This is one of the tools you will need to remove stubborn pre chambers.