Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
This critical coolant hose hardly ever gets changed, and when it ruptures, you could experience a catastrophic engine failure. The chief reason is that it is almost impossible to see and inspect.
Set of upper and lower main radiator hoses as shown.
in this detailed 38-minute video Kent will walk you step-by-step through the procedures of removing the old belts, installing the new belts, and tightening them properly. When changing your V-belts there are other things you should consider replacing as well.
If your engine is taking too long to heat up or is constantly running "hot" it is probably time to replace the thermostat. Kent explains in the video below some other parts you should consider replacing at the same time.
New water pump and gasket as shown. Plan to change the short hose and thermostat at the same time. Inspect v-belts and change if cracked.
The bearing in this pulley wears out at 80,000 to 120,000 miles and can cause rumbling sounds while the engine is running. A good time to plan to replace or at least inspect this is when you change the V-belts.
If you have one belt that is going bad, replace them all simultaneously. You don't want to have to do this job again in the near future.
Almost every early SL Kent comes across needs new front wheel bearings. These get so neglected and hardly ever replaced. We are offering a very high quality kit as shown above that will include free grease for your new wheel bearings.
No cracks or chips. Very good used condition as shown. These are the parts you will receive.
Inspect for adjustment and tension. If you disconnect the cable from the throttle linkage and there is no spring back pressure then the cable is broken.
New o-ring seal installed.
When pressure testing your KE-jetronic fuel injection, you may find you need a really thin wrench to install the small fitting on the right side bottom of the fuel distributor.
This accumulator was unique in the mid to late 1970s. It was used on all 6.9s but only some 450 V8 models. That is why you MUST know which type you have BEFORE ordering. You can clearly see the two threaded holes coming into the front of the accumulator housing.
As a safety preventative measure, replace this hose if it shows signs of hardening or cracking. This hose is under 90 psi; if it cracks and spews fuel, you can have an instant engine fire.
This Introduction manual is intended to familiarize technical personnel with the Registration year 1976 Passenger Cars. This covers changes and new developments, it does not cover all repair information on the included chassis. 87 Pages
30 light bulbs total in this assortment. PLEASE NOTE: These may not be every bulb you will need for every model, but you will have extras on hand. These cars are OLD, and most of the bulbs need to be replaced. They even start to loose some of their intensity over time.
High quality fast break in pads with special coated anti-squeal pad bonded to the back side of the pad. We include 4 new sensor wires and a small ceramic brake pad grease to lube the pad edges and the pins. ( no need to lube the back side).
These WILL NOT work on your original injectors. They will ONLY work on our new replacements (see below) These plugs are a good alternatiive to the damaged originals on your D-Jetronic fuel injected engine IF you are installing our new injectors.
This is what you need as the final touch to get your later 450 engine to run smoothly. New OE Bosch cap, Bosch or Bremi rotor, and new Bremi wires. If you need spark plugs as well please order separately. See related products below
New tensioner as shown. No specific instructions are available but this can be installed from outside the engine once you get access the the hold down bolts.
This video applies to both K-jetronic and KE-jetronic fuel injection engines on Mercedes from 1976 to 1993.. Let's say you just acquired an old gas engined Mercedes and you just can not get it to run right and or even get it to start.
Nice to have a few extra 13mm sockets around. This is the first tool that gets lost when working on old Mercedes. The tall shoulder inside helps to hold the nut or bolt in a position to make it easier to start the threads.
Think age here. Many of these shifters on our classic Mercedes are starting to get loose inside the shifter, and when the old bushings fail, you will get a lot of slop side to side when you shift between gears. Note: These bushings are different from the bushing that go on the shift levers.
ONLY ONE SET AVAILABLE. Three of these wrenches are made by Gearwrench. You get a very long standard combination 13mm wrench, a long 10mm with a racheting box, a very long 17mm with a ratcheting box, and finally, a very long 14mm combination wrench made by Urrea.
This is a great kit for your 350SL, 450SL, 450SLC, 380SLC, 380SL, and 560SL from 1972 to 1989.
These are the critical seals that go on the D-jetronic fuel injectors. If they leak air, your engine with idle high, start poorly and run lean, which can damage the pistons. We recommend you replace these whenever you remove and replace the injectors.
In this 13-minute CIS training video, Kent will walk you through the steps recommended by Mercedes Benz to fully test the operation of the EHA valve on 1984 to 1993 4, 6, and 8-cylinder engines with KE-jetronic fuel injection.
This high-quality meter can test all types of automotive electrical circuits, but Kent has discovered it is particularly well suited for testing Bosch KE jetronic fuel injection components on those CIS models from 1984 to 1993. Extra adapter fittings are included as shown.
Often rotten and torn. Replace with new when working on your fuel delivery system. PLEASE NOTE: These are included when you purchase any of our fuel pump delivery kits.
Replace your old and worn knob with this inexpensive genuine Mercedes part.
After completing the pressure test on your CIS engine, you discover a problem. But how can you find out how to isolate and fix it? This is going to require some research on your part. Start by learning how the system works and how each component plays a part.
In this video, you will see how the gauges are hooked up to a 560SL and how the pressures are read. The length of this 30-minute shows the detail Kent has put into filming all the critical components of doing a KE-Jetronic fuel system pressure test.
This video is specific to K- jetronic fuel-injected engines from 1976 to 1985. This includes the 350, 450, and 280 engines in the R107, W116, W123, and early W126 gas Mercedes. In this 29-minute video. Kent will show you how to hook up the gauge, run the fuel pumps, and complete the test.
There are a few factory recommend procedures and tests you should do before you do an actual pressure test on a CIS fuel-injected engine. In this 20-minute training video, Kent will walk you through these procedures step-by-step.
To do proper system testing on CIS fuel injection, you must find a way to get the fuel pump or fuel pumps to run continuously without the engine running. This can not be done by just using the ignition key. In this 15-minute training video, Kent will show the options available to do this.
This video will help you decide if you want to try to do a fuel pressure test yourself. It is a fairly simple DIY job but will all the confusion and misinformation on the internet; one would believe it is a complicated process that is hard to understand.
6 black plastic clips as shown. Have these on hand any time you need to remove the two vent grills under the windshield
WARNING: MAKE CERTAIN your current injectors are yellow at the top. A restocking fee will apply if you place an order in error. For the 3.5 engine ONLY. See related products below if you have a 4.5.
Let's face it. These fuel tanks and now 50 years old and most are not squeaky clean inside. There is a fuel tank screen that will catch most particles if the screen is in good shape. But I have found that it will not catch the very fine rust particulates that are so common in these old cars.
PLEASE NOTE: Wire color may be all red or all black (depending on stock on hand) Performing some fuel pressure tests on your K-jet or KE-jet engine
If you own or are restoring a CIS fuel-injected Mercedes, a pressure tester is a must-have! This complete kit is not available, but now you can build your own. SEE related products below to purchase.
We know you want the best for your 560 engine. These ARE the best tune-up parts you can buy. To add new spark plugs see related products below:
Complete set of new ignition wires as shown.
People call these two units pressure regulators, but really only one of them is. In this xx minute video, Kent will explain how these are different, what each one does, how to adjust them, and how to test them with a hand pump vacuum tester.
In this 8-minute video, Kent will show you how to quickly depressurize your D-Jetronic fuel system before doing any injector service, replacing any hoses, or hooking up our fuel pressure tester.
In this xx minute instructional video Kent will walk you through the process of hooking up the gauge, taking the proper readings at idle and at rpm, adjusting the regulator, checking for internal leaks, and depressurizing before removal.
This is a VERY important test to do on your old fuel injection V8 engine!
In this 12-minute instructional video, Kent will show you how he installs the rear hood seal on the hoods of the R107 and the C107 built from 1972 to 1989.
Very important part for fresh air supply any time heater or ac is running.