W110 W111 W112 Sedan, BENZ AID - COMMON QUESTIONS AND ANSWERS
87 190E mush prime my engine to start it.
n/I have a 1997 190E 4 cylinder gas Engine.To start my car I have to prime the Engine.Once that is done it start up unless i let it sit for a few hours.Then I have to prime it again.Please Help.
Forums
water pump removal and replacement 1985 380se?
n/a i tried to remove water pump but was unable to remove a bolt that is behind the harmonic balancer. is there a special tool for this or do you have to remove the radiator and the harmonic balancer to get to that bolt?
Chassis Model Number
Forums
82 300TD high operating temperature
kent
1982 turbo diesel wagon. great runner. no mechanical or fuel issues. always ran about 180 or so degrees. just barely above the 175 f mark on the gauge.
recently...maybe over a month or two. it is rising to near
200. (the next hashmark on the guage) or sligly above with in stop and go. and then drops to about about 185-190 at 60 mph. my usual cruising speed.
outside temps around 95 (though outside temp doesnt really have much of an effect...samre readings day or night)
Chassis Model Number
Forums
Transmission
Checking Automatic Transmission Fluid Level
There is a proper way to do this to determine proper level inside transmission
1978 450 SEL High Idle 2000 RPM
I have just acquired a 1978 450 SEL and based on the records the motor has about 35k miles on it since a complete rebuild. It starts up and runs fine (wants to die if you give it gas when cold) once warm. It drives great but the idle is high at about 2000 RPM cold and 1700-1800 warm. Not sure where to start.
Vacuum? Is there an idle control of some sort that could be bad?
I don't see an idle adjustment and don't know these gas engines so I'm lost.
Thanks for any help!
-Mark
Chassis Model Number
Forums
300TD'83 : 617 Turbo Rack Damper
I have the new 617 Turbo Rack Damper and instructions, ready to replace the old one.
Before I start, it looks VERY tight in there!
Do I have to remove the oil filter housing to do this?
No mention of this in instructions, but I've read elsewhere that it is necessary. Thanks.
Chassis Model Number
Forums
15" Wheels for a 85' 300SD
I am now the second owner of a beautifully maintained 1985 300SD. However, I would like to change out the 14" Bundt Alloys with a 15" Mercedes wheel. I prefer the 8 slot chrome wheels I see on 190s and w201s. The problem is this, I cannot find a straight answer on the Benz forums if there are any stock 15" Mercedes that will "bolt" on correctly in relation to offset size.
Any insight would be appreciated.
Mark L
Dallas, TX
Chassis Model Number
Forums
how hot is too hot?
I have driven 8000+ miles in my 300SDL on Ken's dual tank WVO system. I
have had no performance problems from ambient temperatures from 17 degrees F
up to 90 degrees F. I added a CoPilot and accompanying switches from
Greasecar to help control my fuel tank source switches, etc. The CoPilot
comes with a fuel line and coolant line thermometer. I have noted that
Ken's system seems to heat up the oil about 65-70 degrees over ambient
temps. thus, if it is 35 degrees outside, my WVO after my final glow plug
heater and before my lift pump is about 105 degrees.
My research suggests that 150-160 degrees is good, but 250 degrees is even
better.
Even though i have noted no degradation in performance at 105 degrees, i was
Chassis Model Number
Forums
'80 123 Odometer sticks at xx9.9
The odometer sticks at xx9.9...eventually turning again but sticking long enough to make the trip meter useless. It must have been going on for a long time...total miles are under 80K. Something needs some grease?