$86.00
123 300TD Wagon Wiper Delay Relay (used)
ONLY ONE AVAILABLE: Fits Late W123 1981 - 1985 300TD Wagons Rear window wiper. Only
W123, Factory Books and Manuals
1984 300 CD Rear Bumper Corrosion
removed the rear bumper and associated rubber trim pieces because the black trim piece running the length of the bumper was loose. Further investigation revealed it's time to conduct some corrosion control on all the metal parts.
Looking inside the bumper one bumper shock has separated from the bumper. I plan to just drill holes and bolt the bumper and shock back together. However, the bumper is severely corroded where the bumper and bumper shock contact, possibly a case of dissimilar metal contact.
Chassis Model Number
Forums
Fuel Delivery
Removing Stubborn Diesel Fuel Injector Heat Shield Washers with Special Tool
Applies to all 200D 220D 240D 300D 300CD 300TD 300SD 190D 300SDL 350SD and 350SDL
$14.25
61x Diesel Engine Compartment Fuel Hose and Clamp Replacement Kit
For early diesels 1968 to 1985 220D 240D 300D 300CD 300TD 300SD
83 300D Transmission Shift Problems ??
Everything on my car works great except the auto trans and I am by passing that problem by shifting manually.
Question to you "am I doing any damage" by not allowing trans to shift automatically?
Right now, 1st gear shifts out quickly below 10mph, 2nd shifts at 18mph with a huge flair and 3rd shifts a little firm.
What I have been doing is keeping 1st in gear until 17mph (high revs)then manually shifting to 2nd and the shift is smooth as can be! Shift into 3rd manually is around 35mph (high revs)also smooth as silk and then we are off to the races and as long as it's in high gear it will run all day without any problem.
What is your take on what I'm doing as far as future problems being created.
Chassis Model Number
Forums
300D persistant knocking noise
I am still trying to track down a baffling noise that one tech has said is a rod knock. The 300D has 117k miles and has had regular service by the M-B dealer where it was purchased. I am the second owner having purchased the car at 116k.
I have now driven the car 1,500 miles half of it on Interstates. Last weekend I did about five miles at 95mph. The noise hasn't changed the oil pressure still pegs above 3 bar at speed and just below 2 at idle.
I keep thinking that if this was a rod bearing it would have gotten much worse by now.
Chassis Model Number
Forums
84 cdt Cold Morings accelerator sticks down when I'm trying to stop
It only happens sometimes in the first 5 min or so of driving on cold mornings. The accelorater gets stuck on the down position. My brakes hold me back before I drop the transmission into neutral. Obvious concern here, any suggesstions would be appreciated.
Chassis Model Number
Forums
84' 300D reverse lights not working
Hello, the reverse lights in my 84' 300D are not working, the bulbs are good and all other lights now work as intended, I'm thinking maybe something with the neutral safety switch.
Chassis Model Number
Forums
1983 300D Diesel Purge Testimony... Wow!
Hi everyone. I've been a Master guild tech for 9 years. This product calld diesel purge?
I was little hesitant to use this product. I have a 1983 123 turbo diesel that needed some help
With cleaning. Car was sitting for 5 years. Let me tell u this stuff is amazing.
Quick and easy and powerful results.
Wow just Wow. Redbull for cars. Instant power and performance.
Chassis Model Number
Forums
1982 617 balancer install
Kent,
I am replacing the front seal in a 1982 300d. I used the kit and the seal installed quite easily. The problem occurs with the install of the balancer. The two pins are not attached to the balancer on the 300D as it was in my 240D balancer. The problem is that even when I heat up the balancer to 300 degrees in a toaster oven, (it can be positioned for nearly a minute) the pins do not fit into the holes. Every time I try to insert them, they go in partially and then stop with most of the pin sticking out or on a angle.