1965 To 1987 Diesel Prechamber Collar Ring Nut Removal Tool
This tool is required to remove the prechambers in the OM 615, OM 616, OM 617, OM 601, OM 603 four, five, and six clyinder diesels through 1987 ONLY! Easy tool to use.
Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
This tool is required to remove the prechambers in the OM 615, OM 616, OM 617, OM 601, OM 603 four, five, and six clyinder diesels through 1987 ONLY! Easy tool to use.
You can buy a rear rubber seal anywhere, BUT there is nowhere else you can buy one with instructions, tools, and supplies to make it easy for you to do the job right the first time! Kent will show you some tricks that eliminate long-term problems and make it look pretty at the same time.
Only fits years and models noted. WARNING: WILL NOT fit W116, W201 or W124 models. Now comes with both Kent's PDF written manual and the new 44 min. video on removing and installing the new steering lock.
You will need to loosen the bottom of the rear shock, disconnect the control arm from the outer knuckle, loosen the inside arm bolts, and drop the end of the control arm down. Kent designed this tool to make it easy for the DIY mechanic to do this job without having to take it into the shop.
In this 23-minute step-by-step "how-to" video, Kent will show you how to install a new set of fuel injectors in your early D-Jetronic engine. This video is included free with the purchase of our early 3.5 and 4.5 fuel injector sets.
The subjects included are:
It is the bushing you can not see and it is very hard to inspect. There are two ways you can replace them.
PLEASE NOTE: You will get the filter and the gasket for the original transmission pan. Make sure your pan is original! This combo includes the three kits listing below. You will get full video instructions and will help you do this and save big $$$.
These are super absorbent, low lint, and have strong birch handles. More than enough to keep you busy for a while.
Only one available. Please do not try to order more.
These are becoming harder to find in good condition. They were often used as the spare tires in these older models.
Off low mileage coupe and in dry storage for the past 25 years. Excellent condition as shown.
This is actually 2 sets of bumpers that will allow you to make one really good set. I have been working to get a nice pair for the past 20 years to go on that perfect 6.9 but time is running out. On to the next enthusiast.
6 "German style" non-cutting hose clamps as shown. These are wider than most to better seal the hose to the fitting. See our other hose clamp assortments below.
In this collection you will receive the CIS pressure testing short kit and all 6 of Kent's videos on Bosch CIS fuel injection theory, tester connections and testing. Click on each link below to read about the specifics of each. This combo kit overs a great savings.
If you plan to replace, test, or service your electronic fuel injectors you first must determine which bottom seals you will need. If you have a 1970 or 1973 model, you most likely have the single-bottom seal (unless your engine has been changed).
Learn how to install this critical repair kit correctly and how to test your monovalve function on the bench. In this 13-minute video, Kent shares how to install the kit while avoiding problems. Get your cabin heat working properly again!
This fits the U.S. models with automatic climate control which include the 1982 to 1989 R107 380SL, 500SL, and 560SL + the 1982 to 1985 W123 ALL models + the 1981 to 1991 W126 sedan and coupes. This is an easy fix that you can do yourself.
Kent has learned that you really can not tell how good your v belts are by just looking at them, especially if they are over 15 years old. Kind of like old tires - they may look good on the outside.
For E430, ML430, E500, E55. S500, CL500, and SL500 through 2003. Every M112 V8 I have worked on starts making front engine bearing noise around 90K to 100K. Almost like clockwork! This is a service you will want to perform whether you have had your Benz for a long time or just purchased one.
Kent walks you through replacing a trunk seal on a 1970 280SL. The video is 13 minutes long and covers removing the old seal, cleaning the groove, trial fitting the new seal, and the final gluing procedure.
In this 24-minute instructional video, Kent shows you more than just how to change the transmission filter and the pan.
In this 19-minute detail instructions, Kent will show you how to get the old seal out, how to trial fit the new seal, and how to glue it in place properly. You can not believe how many seals we see that have not been installed properly.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
Yes, YOU can fully drain all your transmission without using any type of "power flush." Full detailed video instructions are included. This kit is easy to connect and the process is quick and clean. Watch Kent's YouTube video below for full details.
Only one available used original in good conditon as shown. We also have these new aftermarket. See below.
For the past 20+ years, we have promoted H4 headlight upgrades for these old Mercedes. The original sealed beam headlight bulbs lacked light output, and we found them sometimes downright "sketchy" on dark roads, especially when deer were known to be present.
You will receive ten each of the following sizes: 8/12, 10/16, and 12/22. These are much better than U.S. style hose clamps that cut into the hose.
Kent shares with you 3 key steps that you should consider doing to get your old fuel injected 6 and 8 cylinder engines running properly. These include:
These require removal of the batter and possibly the brake booster to replace. They are split so you do not need to remove the sway bar. Plan to replace if doing work under the battery box area. Battery acid is hard on the right side.
These will no longer be printed when these are gone. They will still be available as a download. All books are signed by Kent. This is an end of an era for us. Most books are approximately 15 pages in length and covered with heavy clear plastic.
DO NOT ORDER UNTIL YOU REMOVE ONE INJECTOR IN YOUR ENGINE AND INSPECT THE HOLE. Sometime in 1974, Mercedes changed the way these injectors were sealed into the head to prevent air leaks. A "YELLOWISH" nylon sleeve was added along with two seals on the lower end of the fuel injector.
This kit has enough red clips (60) to do both sides on the 123 240D, 300D, 300TD, 300CD, 280E, and 280CE. You will receive the best tool to remove the side trim and the best tool to remove the old red clips from the side trim after removal.
Beautiful driver-side front fender, as shown. ALL original light silver blue paint. No rust and no previous damage.
You can not believe how easy it is to move and adjust your old seat after lubrication the tracks with this amazing lubricant! You will receive two full tubes plus the extension nozzle. This is more than enough lube to do the seats with four tracks on each side.
New quality aftermarket part as shown. Door panel must be removed to replace. Fits either door.
These quality 6.5 inch wire cutters are made of special steel, the blades are high-frequency hardened steel. Suitable for cutting soft copper wire, plastic wire, small cable, aluminum wire, soft alloy wire, jewelry making, multifunctional manual edge banding pliers.
I am throwing in the wires for free, so please, no complaints. They work and are not all the same color, but you could use them if you ever need to replace one wire. The two wire holders for the valve covers are also included from free.
GOOD used shoulder harness latch mechanism complete with rail holder and black plastic cover. MAKE SURE your LATCH HOLE is like the one below. Later latches had a smaller slot.
ONLY one available. These are the actual parts you will receive packed carefully.
Excellent used all-metal driver and passenger-side tail light bulb holders for early sedans. The later models were plastic. These are exceptionally nice units with very bright reflectors and clean bulb sockets.
PLEASE NOTE: We do not sell the coil-over shocks. These can be purchased from numerous sources online. Kent used the shocks from Hiro Performance. You can use google to find these sources.
These are the rubber parts that often do not get replaced when working on an R107 front end to fix loose steering, squeaking noises, and erratic handling. These fit all 107s from 1972 to 1989.
A good kit for your R107 restoration. It includes a new OEM rear hood seal, a new aftermarket heater motor cover, and a hood opening extender to make installation SO much easier. Read a full description for each item below by clicking on the links.
In this 15-minute video, Kent will show you step-by-step how to safely remove the Bowden cable without damaging it and how to install it to get the proper connection. This is not as easy as it looks, and you can break it if you are not careful.
In this 9-minute instructional video, Kent explains how to set up his injection pump cleaning and testing kit ( available separately ), and use it to clean out old fuel injection pumps of gum and grime, and then how to test them to make sure they are delivery fuel through every line.
This is the best way to determine if the expensive injection pump is going to work for old 4 AND 5-cylinder diesel engines that have not run in years. Watch the video below to understand what this kit can do.
Watch the video below to understand what this kit can do. Ensure your injection pump is thoroughly cleaned and lubricated before starting the engine after long storage.
We know you will be very happy with the quality of these plastic headlight surrounds!
These are rare and very collectible for the performance enthusiast. Each book contains the following: IIS
Here are the titles, dates of printing, and total pages in each of these four factory training booklets. IIS