Some of Kent's Mercedes Benz Collection on Sale! CLICK HERE to view all.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
Yes, YOU can fully drain all your transmission without using any type of "power flush." Full detailed video instructions are included. This kit is easy to connect and the process is quick and clean. Watch Kent's YouTube video below for full details.
For the past 20+ years, we have promoted H4 headlight upgrades for these old Mercedes. The original sealed beam headlight bulbs lacked light output, and we found them sometimes downright "sketchy" on dark roads, especially when deer were known to be present.
You will receive ten each of the following sizes: 8/12, 10/16, and 12/22. These are much better than U.S. style hose clamps that cut into the hose.
Kent shares with you 3 key steps that you should consider doing to get your old fuel injected 6 and 8 cylinder engines running properly. These include:
These require removal of the batter and possibly the brake booster to replace. They are split so you do not need to remove the sway bar. Plan to replace if doing work under the battery box area. Battery acid is hard on the right side.
These will no longer be printed when these are gone. They will still be available as a download. All books are signed by Kent. This is an end of an era for us. Most books are approximately 15 pages in length and covered with heavy clear plastic.
DO NOT ORDER UNTIL YOU REMOVE ONE INJECTOR IN YOUR ENGINE AND INSPECT THE HOLE. Sometime in 1974, Mercedes changed the way these injectors were sealed into the head to prevent air leaks. A "YELLOWISH" nylon sleeve was added along with two seals on the lower end of the fuel injector.
This kit has enough red clips (60) to do both sides on the 123 240D, 300D, 300TD, 300CD, 280E, and 280CE. You will receive the best tool to remove the side trim and the best tool to remove the old red clips from the side trim after removal.
RUST-FREE and damage-free passenger-side front fender, as shown. ALL original light silver blue paint. No rust and no previous damage from being hit.Some peeling of the paint on the top edge due to torch heat to melt the glue they used to at the factory.
You can not believe how easy it is to move and adjust your old seat after lubrication the tracks with this amazing lubricant! You will receive two full tubes plus the extension nozzle. This is more than enough lube to do the seats with four tracks on each side.
New quality aftermarket part as shown. Door panel must be removed to replace. Fits either door.
These quality 6.5 inch wire cutters are made of special steel, the blades are high-frequency hardened steel. Suitable for cutting soft copper wire, plastic wire, small cable, aluminum wire, soft alloy wire, jewelry making, multifunctional manual edge banding pliers.
I am throwing in the wires for free, so please, no complaints. They work and are not all the same color, but you could use them if you ever need to replace one wire. The two wire holders for the valve covers are also included from free.
GOOD used shoulder harness latch mechanism complete with rail holder and black plastic cover. MAKE SURE your LATCH HOLE is like the one below. Later latches had a smaller slot.
Excellent used all-metal driver and passenger-side tail light bulb holders for early sedans. The later models were plastic. These are exceptionally nice units with very bright reflectors and clean bulb sockets.
I call this the hidden and forgotten bushing. Why? Because you can not see it to inspect it, it hardly ever gets changed. When these bushings wear out you will feel "weird" movement in your rear end, especially going over rough ground.
These are the rubber parts that often do not get replaced when working on an R107 front end to fix loose steering, squeaking noises, and erratic handling. These fit all 107s from 1972 to 1989.
A good kit for your R107 restoration. It includes a new OEM rear hood seal, a new aftermarket heater motor cover, and a hood opening extender to make installation SO much easier. Read a full description for each item below by clicking on the links.
In this 15-minute video, Kent will show you step-by-step how to safely remove the Bowden cable without damaging it and how to install it to get the proper connection. This is not as easy as it looks, and you can break it if you are not careful.
In this 9-minute instructional video, Kent explains how to set up his injection pump cleaning and testing kit ( available separately ), and use it to clean out old fuel injection pumps of gum and grime, and then how to test them to make sure they are delivery fuel through every line.
This is the best way to determine if the expensive injection pump is going to work for old 4 AND 5-cylinder diesel engines that have not run in years. Watch the video below to understand what this kit can do.
Watch the video below to understand what this kit can do. Ensure your injection pump is thoroughly cleaned and lubricated before starting the engine after long storage.
We know you will be very happy with the quality of these plastic headlight surrounds!
These are rare and very collectible for the performance enthusiast. Each book contains the following: IIS
Here are the titles, dates of printing, and total pages in each of these four factory training booklets. IIS
Good used LEFT reflector as shown. Not perfect but better than most. This is the actual part you will receive. We cannot guarantee that all the bulbs will work as this part has been in Kent's storage for 20 years.
Failure can cause cabin heat to drop off when the car runs at idle. Easy to check by removing the wiring plug and applying 12v power to determine if it is running.
In this 20-minute instruction video, Kent will show you how to take his short kit and combine it with a tester that you can purchase online to make a leak-free, reliable, and accurate fuel pressure tester for Bosch CIS fuel injection.
Both items you see above with complete video instructions. Click on each product included for more info. There are other parts you may want to replace at the same time such as the water pump, thermostat, short hose, and radiator hoses at the same time. See related products below.
It has been over 30 years since the last Mercedes with Bosch C.I.S. fuel injection was manufactured. If you own a 1976 to 1993 Mercedes gas engine with this type of fuel injection, you may have difficulty finding someone to work on your car. In some parts of the country, it may be impossible.
It seems like you never needed a 16mm or 18mm wrench or socket until 1996. After the intro of the W210 things changed. This set of 3 quality U.S. made tools consists of an 18mm stubby combo, an 18mm deep 3/8 drive socket, and a 16mm short 3/8 drive socket.
These came off a 108 that had been in dry storage for 32 years and only had 68,000 miles on it. What you see is what you get.
USED tank as shown. No leaks. Not perfect, but note the lack of fading and yellowing. Hard to find a better original tank. Comes with cap and pickup tube.
This fits a number of lmid 1960s to early 1970s models with automatic transmission. 250SL 280SL 250S 250SE 280S 280SE 280SE 300SEL. Check under the front of your car to make sure this matches what you have before ordering.
Just so you know, not all parts shown will fit in all years and models of the W108 and W109. There may even be some “stray parts” here that belong to other chassis. These are parts that Kent has collected over the past 25 years.
Flushes Out Old Grease and Repacks Bearings with Less Mess. This Handy Packer works on bearings up to 3 1/2" O.D.
This one is super nice. Has been in storage for 20 years. No cracks, no breaks, no star chips, a good reflector, and an excellent plastic headlight door. Have not tested bulbs so can not guarantee but they most likely maybe will work...
Hard to find and an absolute must to keep from burning out the glow plugs.
These fit all W116 from 1973 to 1980. You will often find these bent or broken. Door panel must be removed to replace them.
Excellent quality zinc plated hose clamps as shown. These can be tighten with a straight blade screw driver or a 7mm socket or nut driver.
Kent is a firm believer in using these strong magnets inside a transmission pan to help extend its useful life.
They should be placed toward the rear of the pan as shown in the picture below.
This is an excellent replacement if yours has melted and deformed.
This the exact puller you will receive. Handy for small jobs.
For ALL 2003 to 2010 7-Speed automatic transmissions( early 722.9 WITHOUT option code A89 indicating reduced friction). These are the 7G transmissions that use the red fluid with the shallower transmission pan. This is a complete kit for your transmission 40K service, not including the fluid.
2FREE limp-home troubleshooting video included! Be forewarned! It is not as easy as it looks on some YouTube videos to remove a valve body and conductor plate from an early 722.9 transmission.
One very minor weakness on the W123 is the glove box door. This is because 2 of the key stress points built into the door are made of plastic. One would be the pin holding the latching mechanism ( Kent already has a repair kit for that - see related products.
Have you ever had to drive to the local hardware store to find a small o-ring? How much did that cost you in time and fuel? These are all small metric sizes. In the picture below, you can see the included sizes.
This can replace that old, hardened, and worn-out seal at the bottom of your V8 air filter housing to prevent dirt and dust from entering your. Check yours soon to see how tight it fits on top of the fuel distributor.