CHECK OUT our new parts and kits for 2007 to 2012 models CLICK HERE to view all.
All 280SL 450SL 380SL 1972 to 1985. All 230SL 250SL 280SL. All 108 and 109 Sedan from 1965 to 1973 including 280SE/L 5.4 and 300SEL 3.5 and 4.5. All 114 and 115 sedans and coupes from 1968 to 1976 including 220D 240D and 300D. We are now offering a kit with 2 new tie rods.
FITS THE FOLLOWING: All Mercedes Chassis 111 113 108 109 107 114 115 116 123 126 from 1968 to 1991 (not applicable for 201 or 124 chassis). This is a very common wear problem on most older Mercedes.
New Drive shaft center support bearing. Fits all 240D, 300D, 300CD, 300TD, 300SD 300SDL 300CE 300E 420SEL 380SE 280SL 450SL 560SL, gasoline and diesel models from 1968 to 1993. This bearing may need replacing on high mileage cars.
I have been discovering this is one of those maintenance areas that suffers from severe neglect. Failure of the rubber support or center drive shaft bearing can cause all types of improperly diagnosed vibration problems - some commonly change with vehicle speed.
When it is time to change the rear end fluid, why not get rid of your old rusty drain plug(s) and replace one or both with stainless steel plugs?
If you have one of our pressure brake bleeders, you can easily attach this wand to the end of the hose by removing the brake master cylinder reservoir cap. You can place the exact amount of fluid in the tank, hang the wand in the fill hole, lock the valve open, and walk away.
This tank works amazing! Put in the heavy rear end or trans fluid. Pump up the pressure. Stick the non-fall-out end in to fill hole... and just push on the valve in the handle of the filling wand.
Have you dreaded changing the rear end fluid before because it is a pain and ends up being really "messy?" Kent finally decided there had to be a better way so he went to work and came up with the idea of using a simple and affordable custom made pressure tank to "flush" and refill differentials
Works on W114, W115, R107, W116, W123 and W126. A better performing and more comfortable 14mm hex wrench to use when changing the fluid in your rear end. Will work on manual transmission with 14mm drain plug only. Watch the video to see why.
This is not a normal nut. On the face it has a special hard plastic nylon seal. When this seal deteriorates you may see evidence of power steering fluid seeping out of the bottom the the adjustment locknut (located on the top of the steering box).
WARNING: IF YOU ORDER THE WRONG ONE IT IS NOT RETURNABLE.
This is a great kit for your 350SL, 450SL, 450SLC, 380SLC, 380SL, and 560SL from 1972 to 1989. It also fits all W114 and W115 Sedans and Couple both gas and diesel from 1968 to 1976. Brand new UPPER control arm inner bushing repair kit.
Brand new upper ball joint assembly with hardware. Fits all 114 115 Sedans and Couple both gas and diesel from 1972 to 1976. Also fit early SL and SLC convertibles and coupes - all 450SL, 450SLC, 380SLC, and 380SL from 1972 to 1985. Replacing the upper ball joint is not a do-it-yourself job.
This is a great kit for you 114 and 115 owners. Fits all Sedans and Couple both gas and diesel from 1968 to 1976. Also fit early SL and SLC convertibles and coupes - all 450SL, 450SLC, 380SLC, and 380SL from 1972 to 1985. Brand new set of 2 lower ball joints. This is not a do-it-yourself job.
Fits all 114 115 116 107 123 124 126 drivelines 1968 to 1993.