$28.00
615 616 617 Early 601 and 603 Diesel Engine Prechamber Collar Nut - USED
For 190Dc 200D 220D 240D 300D 300TD 300CD 300SD 190D 300SDL 1963 to 1987 Pre-chamber (s) ONLY
W110 W111 W112 Sedan, BENZ AID - COMMON QUESTIONS AND ANSWERS
1984 300SD inner fender horn
1984 300SD What is the horn on the passenger fender wall for? I had to remove the fuse to turn it off. Thank you.
Chassis Model Number
Forums
Suspension
Diagnosing Strange Front End Rumbling Noises
Suspect front wheel bearings
1980 300D oil pan heater
Kent,
I recently installed the Meyle oil pan you sell on your website on my 300D. I'm planning to purchase your oil pan heater kit too, but before I do, I wanted to make sure it would work. You warn that the heater won't work on a "ribbed" oil pan, and the Meyle pan does have a few indentations in it. Should I consider that "ribbed," or no? Thanks!
Collin
Chassis Model Number
Forums
Fuel Delivery
Diesel Engine Prechamber Collar Nut Fuel Leaks
A unique special tool so affordable every diesel owner should have one
86 190D Injector knocking/nailing
I've got a non-turbo 190D, 1986, 255k, that was running well. I had some small leaks on the top of the injector pump, so I replaced the orings/seals. After reassembling it, I had a major Knock at just above idle to 1500 or so, and no power/more smoke, as well as an "up and down" idle. I then pulled all the injectors, cleaned them, pressure tested(all from 1600 to 1700), and put a new monark nozzle in #3.
This didn't solve anything, knock is still there, maybe slightly worse.
I've replaced both fuel filters. I've run diesel purge through the system, which does quiet it down. But it comes back when on the main system.
Any ideas where to go from here? Should I replace the knozzles? Could I have messed up the delivery valve seal setup(not sure how, but).
Chassis Model Number
Forums
300D Leaking Valve Cover Gasket
I have completed a valve adjustment and replaced the valve cover gasket. After running the car, oil can be seem around the edge of the gasket where it meets the engine block. The bolts are tight and I donot understand why there is a leak. The gasket was obtained from a OEM operation. Should I get a gasket from the dealer? Have other people experience this problem?
Chassis Model Number
Forums
1985 300TD Wagon, Warped Dash Wood
My zebrano? dash wood that covers the climate control is warped, or cupped. I have the recommended adhesive, and it's worked great on some of the long rectangular pieces of dash trim. I was looking for some advice before I try oiling up the piece of trim and weighing it down with a stack of books.
Any ideas?
Chassis Model Number
Forums
1982 300D Mild engine shake and smoke exhaust at initial startup
I am having a 'rough idle' issue I cannot seem to resolve; I will categorize as mild because I have worked on a two 240D (1980, 1981) and I was able to perform the recommended maintenance to have them idle very smoothly.
Additionally, hard initial start or it quits right after initial startup, then I am getting a blue smoke from the exhaust at the initial startup and for about 10 minutes before complete warmup.
Here is what I have done up to this point using the manuals, advice, and parts from mercedessource:
Chassis Model Number
Forums
1984 model 123 rear window molding
How is this removed? Special tool(s) required? I need to do some rust repair and it looks as if I can leave the rear window in place and just R and R the molding. Probably will have to buy new molding??
There isn't a glass shop here in Baja (Tijuana area) that I trust and I sure cannot afford to take it to the states.
Jim