Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
Nice set of pick tools with plastic handles. They have strong steel tips which allow for more prying and twisting with less tendency to bend the tips as you would with dental pick tools. Note: Quarter is not included! Shown for size reference only
Final drive seal (45 x 65 x 11mm)
Fits Mercedes Benz:
Engine Camshaft Woodruff Key
3 Degrees Offset
Fits Mercedes Benz:
Replace those nuts that keep loosening up with nylock metric nuts that just won't come off. Inside the door panel on the window regulators. Around the engine compartment. Air filter housing nuts. etc. etc.
Fits Mercedes Benz: 280CE
280E
280SE
280SEL
380SL
380SLC
450SE
450SEL
450SL
450SLC
Fits Mercedes Benz: 230 250 280 250S 280S 280C 220 250C
This set of 5 pick tools have very thin and sharp points. Best set Kent has found to remove orings in hard to get to locations. The variety of angles available allows you to get into almost anywhere to remove and o-ring, sealing ring or other small part.
New Plastic Drain Plug. Fits all models listed below:
Mercedes-Benz 240D
Mercedes-Benz 280CE
Mercedes-Benz 280E
Mercedes-Benz 300CD
Mercedes-Benz 300D
Mercedes-Benz 300SD
Mercedes-Benz 300SDL
Mercedes-Benz 300TD
This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.
This sealing ring provides seal at the connection of the flexible down pipe and the exhaust pipe going back to the center muffler. This is an upgrade replacement for the older style crushable gasket seal. This all metal ring provides a much more reliable seal over time.
Here are the correct size metric nuts with built in shoulder washer. If you drop these in behind the injection pump you may never find them. When doing glow plug service it is always a good idea to have some spare nuts on hand. New Bosch glow plugs do not come with new nuts.
This is a common oil leak area on the 300SD. The gasket fits between the oil filter housing and the plate that mounts the oil pressure sending unit. This is a genuine OE gasket.
Application:
Brand new rubber brake pedal pad. Fits many 1960s models. Make sure this will fit your car. This pedal measures at 2 3/4 height x 2 3/4 width at largest part.
New rubber stop for rear exhaust bracket. It plugs into the body right above the back of the rear muffler. Helps prevent rattle. Fits almost all models from late 1960s to mid 1990s. When you hear something clunking in the back when you go over a bump, this part is probably missing.
Brand new electric fan motor switch as shown. This fits on the thermostat housing and is set to cycle at 212 degrees F. Fits all 123 models 1977 to 1985 and all 116 and 126 300SD up to 1984 only.
A faulty switch can cause you fan to stay on all the time or not come on at all.
High Quality (made in USA) brass two way fuel rated valve with brass fittings for 3/8 inch fuel hose. Can be used to select between two fuel tanks or as a control valve for your loop or return fuel with running on SVO.
Long drive pin punches are very handy when working on your Benz. The smaller size in this set is particularly helpful when removing and replacing twin pin style brake pads. All steel. Made in India. Pin sizes: 1/8'', 3/16'', 1/4'', 5/16'' and 3/8''
New metal end piece with set screw that connects to the linkage on valve cover on 1977 to 1979 300D CD and 240D. Check your cable for an exact match before ordering. This piece always seems to get lost and can be hard to find.
Brand new oil pan repair kit. Includes new pan, new pan gasket, and new oil drain plug. Fits 115 chassis 220D, 240D and 300D. Also fits all 123 chassis non turbo 300D diesels from 1977 to 1981, and 240D from 1977 to 1983. Gasket and drain plug included, but not shown.
This is the number one cause of a sharp engine rattling noise at idle on the early 602, 603 and 604 engines. It is not that the shock goes bad, but the bushings car wear out prematurely due to harsh vibration and the ends of the shock will make a terrible noise inside the loose bushing.
New OEM high quality air filter. Fits 1990-1993 300D 2.5 and 1995 E300D only.
New OE Reinz head gasket set. Fits all 115 and 123 300D 5 cylinder non-turbo engines 1975 to 1981. Comes complete with all gaskets only as shown in the picture. Valve stem seals and valve cover gasket are NOT included.
This is a great gift for the older Mercedes Benz Enthusiast! Sold in increments of $25. This gift certificate can be toward the purchase of any item or items on our website .
This kit includes a New Mercedes OEM fuel tank filter screen along with a special tool I have made to remove and install it. It will save you the time and expense of running out and buying a great big Allen wrench.
Replace your old worn and weak expansion tank cap to eliminate minor coolant loss problems. Watch the video below as Kent will explain the difference in caps and why you want to make sure you purchase the correct one.
Brand new balanced compressor wheel as shown. Increase horsepower by installing a new compressor impeller. The sharp clean edges really make a difference in compressor boost output. Most of these old wheels are worn. No instructions included.
Brand new electronic oil pressure sending unit. If your gauge is erratic or it suddenly has been reading very low, this electric sender may be the culprit.
Fits all the following models listed below:<p>
ONLY one available. These are the actual parts you will receive packed carefully.
This video will take all the "mystery" away... For all W116, W123, and W126 Turbo Diesel 5
Here is a brand new set of four exhaust "donuts". Check your existing rubber hangers on your exhaust. If they are cracked replace them before you lose your mufflers! If your exhaust is rattling, these should fix the problem. Fits all chassis models 108 107 113 116 123 126.
If your modulator is working ok, but leaking transmission fluid, you may only need to replace the inexpensive oring ( o ring ). You do have to be careful when removing the modulator from the transmission. For instructions (available separately) see related products below.
Maintenance Alert: We have had lots of reports of these bolts loosening up! They WILL shear off if not caught early enough. When that happens the pulley will fall off. At high speed this can lead to engine overhead and even a damaged radiator.
If you plan to change coolant hoses this is a must-have labor-saving tool. This is one cleverly designed tool. I could not have done it better myself. I actually use to make a couple of different types before I found this one.
Fits 123 chassis non-turbo models only. This includes 240D, 300D, 300CD to 1981 and 300TD.. These air cleaner housing rubber mounts break and can cause your air filter housing to rattle on the engine. Grab a hold of your housing and see if you can lift it up.
Fits chassis 116 123 126 124 and 201 Diesels with pencil glow plugs, from 1978 to 1989. This includes the OM617, OM601, OM602, and OM603 engines. They also work on 1977 to 1979 300D 300CD and 300TD with series glow plugs. This pack includes three individual fuses.
For reasons of hoping to solve fuel filter leak problems Mercedes changed the center bolt design in some 1984 to 1985 model 123 300D 300TD 300CD and 126 300SD. Instead of one o-ring on the bolt they changed it to two orings (as shown iin the picture.
This item can only be shipped UPS Ground because it is a liquid. One Liter of correct Power steering fluid. Fully compatible with Dexron II systems but has enhanced aditives to reduce steering box gear wear.
Yes, with age they can leak from the inside out ever so slowly. Replace before they fail! This is a great upgrade that fits most models from early 70s up to mid to late 90s. The wire protector on these hoses will prevent chaffing especially from loose V belts.
This is such a big problem on the early 1977 to 1979 123 300D, 300CD and 300TD diesels that I decided a good replacement kit was in order. Often I find the main feed wire loose or frayed, the fuse box cracked or melted, and the fuse connector points corroded or loose.
When replacing front brake discs on above chassis it is highly recommend you replace the bolts that hold the rotor to the bearing hub. Not needed on 201 124 or 129 chassis. Sold individually. 5 required per wheel.
This is one of the more common oil leaks I see on the 602 (5 cylinder) and 603 (6 cylinder) diesel engines. In fact, I have seen it on almost every one of these engines I have worked on.
Fits later 107 and 123 as well as 126, 201, and 124 chassis oil caps (black plastic). Tired of having a hard time getting your oil filler cap off without using pliers. Or are you tired of the unsightly oil leaks around the cap. These gaskets can help solve those problems.
When replacing the thermostat in your order diesel you may end up fitting a lot of corrosion. This kit will help you make sure you do not have any leaks when you install the new thermostat and will prevent corrosion of the housing bolts in the future.
New in 2023. This is "almost" ready to install. You will need to install some parts from your existing turbo charger once you remove it from the engine. Watch the video below for a full explanation.
WILL NOT FIT 85 CALIFORNIA MODELS!! It will fit some 1985 Federal Models only.
For use with the following modesl below. Check size if unsure.
SLS low pressure hose from bottom of reservoir tank to the engine driven pump. Includes 1 meter of heavy duty fuel hose that holds up better to the hydraulic fuel than the old style original braided hose.
PENCIL GLOW PLUGS ONLY!! WILL NOT WORK ON MODELS WITH THE OLD STYLE LARGE THREAD SERIES TYPE. For 1978 to 85 300SD Turbos / 1980 to 93 240D / 300D 300TD 300CD 190D 300SD 300SDL 350SDL. When was the last time your glow plug chambers were reamed out?
It is hard to find the right motor mount bolts for the 116 diesels. They have to be good hard steel and just the right length. We have provided locking washers to install with the bolts so they will not loosen up.