ALERT: Miracle Paint is back in stock! CLICK HERE to order.
New high quality replacement oil sealing rings for the main shaft (front and rear) of the Garrett T3 Turbo. This will NOT fit other turbo chargers like the KKK.
Fits the following, 201, 124, and 126 chassis with 6 cylinder single cam gas engine. In my opinion, the 103 6 cylinder gas engine (built from 1986 to 1993) is one of the best engines Mercedes has ever built.
Covers 190D 300D 300TD 300SDL 350SD 350SDL 1984 - 1993. Book 4 in our glow plug series explains how to properly remove and replace the glow plugs in the OM 601 602 and 603 diesel engines from 1984 to 1993.
This guide will explain how to properly change the fluid and filter in your late 123, 126, 201, 124, late 107 chassis Mercedes as well as early 129 and 140 chassis. This includes model years from 1982 to 1993.
Installation instructions specific for 123 / 126 chassis only - general for other chassis. Details included on how to make your own fuel tank outlet hose and fitting with materials supplied in the Flexible Fuel Line Replacement kit.
This instruction booklet is meant to be an introduction to simple rust repairs. I have also written a manual that goes into more advanced repairs using Miracle Paint to replace larger rotted sections of sheet metal.
Brand new rear end differential front seal. Fits both gas and diesel models. This is NOT the seal for the axles.
Dirko sealing compound is permanently elastic, cold vulcanizing, silicone-rubber based. Can be used for connecting joints, cylinder head, crankcase, oil sump, timing case, thermostat, water pump, transmission, axles, differential, radiator, chassis.
General-purpose, clear RTV indoor/outdoor sealant. Seals, bonds, repairs, mends and secures glass, metal, plastics, fabric, vinyl, weather stripping and vinyl tops. Protects and repairs electrical wiring. May be applied to horizontal or vertical surfaces. Waterproof and flexible.
Sil-Glyde is a silicone based brake lubricant recommended for the entire brake assembly and is compatible with rubber. It is moisture-proof and heat resistant to +600 degrees F, which means it won't burn-off like other brake noise products.
Cold Weld sets up in 15 minutes and has a test proven strength greater than 3000 psi after 16 hours. Resistant to most shop fluids including: water, diesel, fuel, gasoline, antifreeze, hydraulic fluids, motor oil, and transmission fluids. Can be drilled, filed, sanded, machined and painted.
This is a must-have if you have a prized Benz or any car you don't drive often!! If you let any of your cars sit for long periods ( generally over 30 days) without driving them, you can ruin your battery, especially if you let it go completely dead.
Fits all DIESEL ENGINE exhaust systems for 115, 116, 123, 126, 124 and 201 chassis from 1968 to 1995. If you are looking for a more robust exhaust hanger this is it! It is a stronger and more secure exhaust hanger than the standard round rubber type.
Complete valve stem seal set for the 603 engine.
This is not a normal nut. On the face it has a special hard plastic nylon seal. When this seal deteriorates you may see evidence of power steering fluid seeping out of the bottom the the adjustment locknut (located on the top of the steering box).
This is a special pre-chamber collar nut removal socket ONLY that works on the diesel engines in the 1990 to 1991 350SD 350SDL (126 chassis), 1990 to 1993 300D 2.5 (124 chassis), and 1992 to 1995 300SD / S350 (140 chassis).
This is a special pre-chamber threaded fitting that you can attach to YOUR slide hammer to remove the pre chamber on 1990 to 1991 350SD 350SDL (126 chassis), 1990 to 1993 300D 2.5 (124 chassis), and 1992 to 1995 300SD / S350 (140 chassis). You will need to own or purchase a 5 lb slide hammer a
Brand new passenger side rear door power window regulator. Motor not included
Fits the following 126 models:
Only two available at this price. Quality new part made by VDO.
126 Sedan 1981 to 1991 Driver Side Rear Door Window Regulator
Fits the following 126 models: after early vin number noted.
Brand new gasket. Make sure this fits your transmission before ordering. No returnable if ordered in error.
This is a huge improvement over the older torque wrenches that I have seen around for years. I know it is a little more expensive, but after you use it, you will agree it is well worth the money. It is perfect for spark plugs and mid-size fasteners around the engine.
Nice set of pick tools with plastic handles. They have strong steel tips which allow for more prying and twisting with less tendency to bend the tips as you would with dental pick tools. Note: Quarter is not included! Shown for size reference only
This is Kents new favorite ratchet wrench for turning engines over during service and repair. There are a number of maintenance procedures that require you rotate the engine over by hand.
Final drive seal (45 x 65 x 11mm)
Fits Mercedes Benz:
Replace those nuts that keep loosening up with nylock metric nuts that just won't come off. Inside the door panel on the window regulators. Around the engine compartment. Air filter housing nuts. etc. etc.
Excellent used flywheel. Has good gear teeth for starter motor.
If you already have or are willing to buy a 5 pound slide hammer this special threaded fitting will allow you to PULL the pre-chamber from the cylinder head once you have removed the collar nut and the glow plug ( a collar nut removal tool is required look below to learn more).
Good used ring for flywheel bolts as shown. These often get damaged with you have to cut one of your flywheel bolt heads off.
Brand new alternator drive Serpentine belt for 6 cylinder Mercedes Diesel 603 Engine.
This is one of the more common oil leaks I see on the 602 (5 cylinder) and 603 (6 cylinder) diesel engines. In fact, I have seen it on almost every one of these engines I have worked on.
A set of six new high-quality stainless steel short bolts with wave washers is included, as shown. These mount the vacuum pump to the engine block. It is very common for this type of hex bolt to round out when removing them from the vacuum pump.
I have used a lot of different clamping tools over the years to prevent fluids from leaking out when removing coolant, fuel, or brake fluid hoses. Most work ok. Some are hard to use in tight places. Many do not stop every last drip from coming out of the hose.
Fits Mercedes Benz Models:
Grommets push into the holes in the trunk to hold the emblems for the right and left side as applicable. A must have if you plan to repaint your car. Video on how to remove your emblems without damaging them is included free. These will work on the following models.
Mercedes-Benz 230
This set of 5 pick tools have very thin and sharp points. Best set Kent has found to remove orings in hard to get to locations. The variety of angles available allows you to get into almost anywhere to remove and o-ring, sealing ring or other small part.
When replacing front shocks on the above mentioned Mercedes you must a 10 mm 12 point shock with 3/8 inch drive. If you don't have one you will in trouble.
This is a high quality thin wall socket made in Taiwan.
This set of special tools is designed to help speed the removal and ease the overhaul of a Garrett T-3 turbocharger on a 617 turbo diesel engine.
If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.
Works on 110, 115, 116, 123, 201, 126 and 124 diesel engines 200D 220D 240D 300D 300CD 300TD 300SD 190D 300SDL. We have found that over half of the deep sockets we test will not go over some of the longer injectors.
Maintenance Alert: We have had lots of reports of these bolts loosening up! They WILL shear off if not caught early enough. When that happens the pulley will fall off. At high speed this can lead to engine overhead and even a damaged radiator.
For use on 220 240D 300D 300CD 300TD 300SD 1968 to 1985. NO INSTRUCTIONS INCLUDED: The tool is meant for someone who has the factory manual or who already knows how to adjust their injection pump timing on the older diesel engines. Injection pump timing is critical for peak performance.
Brand new Meyle Auxiliary fan motor for 6 cylinder diesel engines from 1986 and 1987.
Fits 300SDL 300D 300TD 300SD 350SDL S350D 1986 to 1993
PLEASE NOTE THE FOLLOWING:
New coolant temperature sensor for most Mercedes built from 1973 to 1993, Gasoline and Diesel models. Many gas models it is located on top of the thermostat housing. Sends signal to engine coolant temperature gauge on the dashboard. These are getting harder to get. Single pin
Kent originally wrote this manual to go along with our 617 Turbo Diesel Front Crank Seal Replacement Kit as well as our 616 and 617 NON Turbo Crank Seal Kit. We have found that many of you are having problems with your front crank bolt loosening up or bolts sheer
This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your 601 602 or 603 diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.
This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.
New turbo charger turbine shaft and exhaust turbine wheel as shown. This part has been highly balanced and is ready for installation. Make certain your compressor wheel is not bent or damaged as that could throw it out of balance. Comes with new shaft nut.