Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
UPS GROUND ONLY: This is the best spray can paint Kent has found to detail the semi-gloss black parts on your Benz. It is not easy to find a good spray can paint!
2 large style clamps to be used on upper and lower radiator hoses. Use these to replace your thermostat or water pump without having to drain all your coolant out of the radiator. Works on medium size coolant hoses also.
We have been looking for a long time to find a super strong and well made tool to adjust those tough 17 mm ball adjuster sockets on the early 4 and 6 clyinder gas engines.
Want to try to make your car's engine and engine compartment look like it just came off the showroom? Would you like detailed information on the chemicals, brushes, tools, and procedures Kent uses to get his engine compartments looking so nice?
Valve adjustment is often neglected on many of the mid 1950's to early 1970's 6 cylinder single overhead camshaft gas engines. If it has been years since any adjustment was made, there will be problems - Kent can guarantee it!!!
If your engine is just running hot, it may be due to a plugged radiator or possibly a stuck thermostat. If your engine is just losing coolant it could be a leak in the water pump, radiator or hoses.
Dirko sealing compound is permanently elastic, cold vulcanizing, silicone-rubber based. Can be used for connecting joints, cylinder head, crankcase, oil sump, timing case, thermostat, water pump, transmission, axles, differential, radiator, chassis.
This is a very handy smaller torque wrench to have in your toolbox. Perfect for spark plugs. It will do fuel injectors but is not quite big enough to torque wheel lug bolts. Range is 5 to 80-foot pounds. The case will be black rather than red.
If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.
This right angle screwdriver is great for working in tight places - like removing speakers, voltage regulators, distributor caps, etc.
January 2019 notice: This filter is now available only in very limited quantities and may not be readily available in the future. This is why we are not able to include it in our full fluid flush kit ( See related products below) This is an often neglected filter.
High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.
Another High Quality product from Lubro Moly. This is a 300ml can of Motor Oil Saver. It Rejuvenates rubber and plastic engine seals and reduces oil consumption via the piston rings and valve guides; counteracts the loss in viscosity of motor oils.
New rubber stop for rear exhaust bracket. It plugs into the body right above the back of the rear muffler. Helps prevent rattle. Fits almost all models from late 1960s to mid 1990s. When you hear something clunking in the back when you go over a bump, this part is probably missing.
Applies to 111 113 108 109 107 114 116 126 Chassis Mercedes.
If you plan to change coolant hoses this is a must-have labor-saving tool. This is one cleverly designed tool. I could not have done it better myself. I actually use to make a couple of different types before I found this one.
Almost all Mercedes gas and diesel engines from the late 50's up to the early '90s used pressed in steel pins to hold the timing chain guide rails in position (inside the engine block).
In stock and ready to ship. New aftermarket fan clutch replacement for 113,111, 108 and 109 chassis gas engines from 1968 to 1973, all 114 and 115 gas and diesel, all 123 gas and diesel engines 1977 to 1983 and 1981 to 1983 126 300SD.
This "permanent" red threadlocker is probably the best that I have used. It has the best sealing cap and cures rapidly and reliably when confined between metal parts. Use it to lock threaded fasteners, nuts, bolts and screws from loosening.
FITS THE FOLLOWING: All models PON, FIN, P55, 110, 111, 112, 113, 108, 109, 114, 115, 107, 116, 123, 124, 126, and 201 chassis. Here is my all time favorite gasket maker and sealant. You may already know how I feel about RTV silicone products (I think they should be outlawed!).
Applies to all Mercedes: Pre 1960, 190SL, 110, 111, 112, 113, 114, 115, 108, 109, 107, 116, 123, 126 with adjustable valves. We have had a number of requests to provide our customers with a feeler gauge to adjust their valves, particularly on the 616 and 617 diesel engines.