Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
Works on 110, 115, 116, 123, 201, 126 and 124 diesel engines 200D 220D 240D 300D 300CD 300TD 300SD 190D 300SDL. We have found that over half of the deep sockets we test will not go over some of the longer injectors.
Maintenance Alert: We have had lots of reports of these bolts loosening up! They WILL shear off if not caught early enough. When that happens the pulley will fall off. At high speed this can lead to engine overhead and even a damaged radiator.
For use on 220 240D 300D 300CD 300TD 300SD 1968 to 1985. NO INSTRUCTIONS INCLUDED: The tool is meant for someone who has the factory manual or who already knows how to adjust their injection pump timing on the older diesel engines. Injection pump timing is critical for peak performance.
Brand new Meyle Auxiliary fan motor for 6 cylinder diesel engines from 1986 and 1987.
Fits 300SDL 300D 300TD 300SD 350SDL S350D 1986 to 1993
PLEASE NOTE THE FOLLOWING:
New coolant temperature sensor for most Mercedes built from 1973 to 1993, Gasoline and Diesel models. Many gas models it is located on top of the thermostat housing. Sends signal to engine coolant temperature gauge on the dashboard. These are getting harder to get. Single pin
Only one available as shown. This is a good working latch but it does have one problem. I have seen these get so badly rusted and corroded that they are impossible to repair. Not the problem with this one. Very clean and no rust.
Hard to find. Good used working Bosch part to control speed of the rear wiper. Confirm your part number 123 821 01 63
Very good Emblems. Bright chrome and super straight.
Kent originally wrote this manual to go along with our 617 Turbo Diesel Front Crank Seal Replacement Kit as well as our 616 and 617 NON Turbo Crank Seal Kit. We have found that many of you are having problems with your front crank bolt loosening up or bolts sheer
This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your 601 602 or 603 diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.
This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.
New turbo charger turbine shaft and exhaust turbine wheel as shown. This part has been highly balanced and is ready for installation. Make certain your compressor wheel is not bent or damaged as that could throw it out of balance. Comes with new shaft nut.
Brand new Head gasket set for 6 cylinder diesel engines from 1986 to 1987. Does not include valve cover or valve stem seals.
PLEASE READ CAREFULLY. This line will not fit the 601 602 and 603 diesel engines produced from 1984 to 1995. If you order in error this part is not returnable. See applicable models and years in subtitle. We had this new straight hard line specially manufactured for us in Germany.
Every one of these pumps I have ever seen needs resealing. The seals and o-rings become just too hard over all those years of use. This is the most complete SLS (self-leveling suspension) pump overhaul kit on the market today.
Genuine Mercedes part. There are 4 clips that hold each of the two intake air grills (below wiper blades) to the bottom. If you are planning to remove them I recommend having new clips on hand. You need a total of 8 per car.
Brand new door striker for Right hand side, Front or rear.
New Behr thermostat 80 degree C with gasket. Comes with illustrated installation tips. Instructions are specific for early 603 engine 1986 and 1987 but will apply to other models as well (some specific details may not apply to the later models).
Fits the following models:
New valve cover gasket for applicable models listed below with 603 engine.
This is a handy compact winch pulling tool. Not designed for lifting. It is a must have if you plan to replace the guide rods or guide rod mounts (brake control rod bushing) on any 126 chassis from 1981 to 1991 300SD 380SEL 500SEL 380SEC 300SDL 350SDL 300SE 300SEL 420SEL 560SEL 560SEC.
Quality German oil filter quantity of 2. For 450, 380, 500, 420, and 560 engines.
Easy to replace. You do not need to get under the car. Access to the lid is on the right side of these engines just below the forward section of the valve cover.
New Fuel tank sending unit o ring. If you need to remove your sending unit to test or clean, it is a good idea to replace o-ring.
Fits 116 107 123 and 126 Chassis from 1977 to 1991.
New AFTERMARKET rubber antenna to rear fender seal. Genuine OEM no longer available. Replace if cracked to avoid water getting in the trunk.
SOLD IN PACK OF FOUR. These clips attach your lower mouldings at the bottom of the doors and bottom of front fenders. Rocker panel moulding retainer. Plan to have some spares on hand if you are removing the mouldings for car repaint or repair.
Use this gasket kit to install a rebuilt or good used turbo charger on your engine. Does not include exhaust manifold to engine block gasket but you do not need to remove the exhaust manifold to change the turbo. This is a gasket set only. NO INSTRUCTIONS INCLUDED.
This right angle screwdriver is great for working in tight places - like removing speakers, voltage regulators, distributor caps, etc.
Common breakage item. Plastic lock pull knob screws onto this rod. For right or left FRONT door.
Rubber engine motor mounts are a very high failure rate part on these cars due to both age and mileage. Have you noticed your Mercedes 240D sedan is recently shaking more at idle. Maybe you just thought it was because it was a four cylinder.
-Please note 9 bolts required per engine
New rubber gasket type with hole at side.
Use this special swedge fittings when making any type of copper coil coolant heater for our SVO WVO fuel system. One end of this fitting clamps down tight on the copper pipe and the other end can accept any standard fitting with 1/4 inch male national pipe thread.
Use this special swedge fittings when making any type of copper coil coolant heater for our SVO WVO fuel system. One end of this fitting clamps down tight on the copper pipe and the other end can accept any standard fitting with 1/4 inch male national pipe thread.
Very nice part. Only few very very minor scratches from having sat on shelf for so long. If you have a 140 you might want to pick this one up for a spare. These are very expensive from the dealer.
If your window washer pump is running and the squirter nozzles are not working properly, you may need replace them with new VDO / Siemens parts. There is nothing like seeing where you are going! Sold individually.
This is one of Kent's favorite tools. Lets you reach into tight places - very long nose curved pliers with teeth - like hemostat. With the locking handles it is amazing what this clamp / pliers can hold - and the tight places it can get into!
Correct metric hex bolt to mount the front crank pulley to the crank counterbalance. These bolts become rusty, are easy to round out, and sometimes even break duty to engine vibration. Check the torque of these bolts.
New Plastic Drain Plug. Fits all models listed below:
Mercedes-Benz 240D
Mercedes-Benz 280CE
Mercedes-Benz 280E
Mercedes-Benz 300CD
Mercedes-Benz 300D
Mercedes-Benz 300SD
Mercedes-Benz 300SDL
Mercedes-Benz 300TD
January 2019 notice: This filter is now available only in very limited quantities and may not be readily available in the future. This is why we are not able to include it in our full fluid flush kit ( See related products below) This is an often neglected filter.
WARNING: IF YOU ORDER THE WRONG ONE IT IS NOT RETURNABLE.
Set of 2 rubber motor mounts. These mounts fit TURBO DIESEL 300CD, 300D, 300SD, 300SDL, 300TD, and gas V8 380SE, 380SEC, 380SEL, 420SEL, 500SEC, 500SEL, 560SEC, 560SEL. These are high failure rubber parts on older cars.
Bad rear mount can cause excessive engine vibration. No instructions included at this time.
Fits 190D, 190E, 260E, 300CE, 300D, 300E, 300SDL, 300SL, 300TD, 300TE, 350SD, 350SDL, 500SL, E300, E320, SL320, SL500
Brand new Hazard Flasher rocker type switch, located in Center console between window switches for 240D 300D 300TD 190E 190D 300SD 420SEL 380SL and other models from 1982 to 1991. If you are unsure it will fit your model, visually verify picture with existing switch.
I like the convenience of using the factory jack points (holes) but I absolutely DO NOT like using the factory jack - except in cases of emergency road side repair. You all know it can be a little unstable... I solved this problem by using a large heavy duty bolt.
SPECIAL ORDER PART -- MAY BE UP TO A WEEK BEFORE SHIPPING!
We are the only company in the world that will offer you a master cylinder with a bench bleeding kit and full 30-minute video instructions on how you can do this yourself!
This kit will work on the following models:
This is a very important maintenance item for 126 300SD 5 cylinder turbo diesel owners. When these belts get loose or worn they can cause all kinds of problems like poor battery charging, engine overheating, jerky power steering, and noises that range from squeaking to rattling.
