When replacing the front struts ( shock absorbers ) on a W201 W124 or some W129 chassis it is frustrating and time-consuming trying to remove and replace the big 22 mm top nut on the front struts ( shocks ).
Search | W124 | Suspension
Over the years Kent has used a number of different things to place on top his jack stands to prevent damage and for added security. He has even tried some of the commercially available jack stand plastic covers. Nothing has proven to work better than the special cut reinforced hose shown here.
In this video Kent will demonstrate how to replace the REAR shocks in the chassis mentioned above. He will do this on the ground on his W124 coupe using a floor jack, jack stands, and hand tools.
In this video Kent will demonstrate how to replace the FRONT shocks in the chassis mentioned above. He will do this on the ground using a floor jack, jack stands, and hand tools.
This is the best one Kent has ever used and he has tried quiet a few kneeling "aids". With 6 wheels this one is strong enough not to break in the middle. In indents with the knee foam are very comfortable.
All these 124 chassis cars are 20 years or older. That is when rubber parts start to fail regardless of mileage. If you want to restore the factory ride and handling Kent strongly recommends you replace the top rubber mounts when you replace the shocks.
Have you ever tried to mask off your tires with paper and tape before painting the wheels? If you have I am sure you are laughing right now. Doesn't work too hot...Hard to get any tape to stick to the rubber tire.
This green colored grease is specially formulated to work on any Mercedes from wheel bearing. Comes in a tube that is enough to do two front wheel bearings and inside hubs. If you drive at high speeds this is your best grease to prevent bearings from overheating.
Fits right or left side. New Bilstein front strut as shown. Please check your vin number before ordering.
To add our new front strut boot and stop buffer kit look below.
Here is my all-time favorite gasket maker and sealant. You may already know how I feel about RTV silicone products (I think they should be outlawed!). We have had a number of our customers ask us where to get this so we decided to offer it on our website.
In this video, Kent will show you how he fixed his leaking tires on his chrome alloy wheels by using Miracle Paint. This is a full 22-minute step-by-step instructional video. Watch the video "trailer" below to give you a better understanding of what is involved in this procedure.
Not complete. Good for parts. One of the fitting threads in the housing was stripped out and a helicoil inserted but at a different thread pitch. The back of the body plate has heavy corrosion but is till usable. If someone needs parts this could help restore another leveling valve.
This will hold the top of the strut and keep it from turning when removing and installing the 22mm nut.
High-quality socket made in Taiwan.
Here you can see how it fits into our magnetic rear end plug:
This is a tool that Kent first thought about making 20 years ago. While installing shock absorbers in his 380SL he had finally had enough - so it was back to the machine shop to come up with a new tool.
In this video, Kent explains the correct procedure for cleaning and lubricating your hubs and rear brake rotor BEFORE you install your wheels. He hardly ever sees this done when removing wheels on 15 plus-year-old Mercedes so he knows it is almost ALWAYS neglected.
I do not need to say much about this tool. Well made and well thought out. Someone who obviously was frustrated at scratching the finish on his or her alloy wheels came up with this idea. Watch the video below to see why this is now my favorite go it 17 mm lug bolt socket.
This U.S.A. made 17 mm 8 inch long combination wrench is custom modified here in our shop to help you easily install Bilstein front and rear shocks on most of the older model Mercedes Benz.
In this video instruction, Kent will demonstrate how to check for one possible source of a mysterious front end clunking sound. Any clunking noise you hear when driving over rough ground or when braking should be investigated immediately.
Trying to fix a rough or bouncy ride in your SLS Mercedes? Not sure what is causing the problem? Maybe you have heard that it might be the accumulators.
In this video Kent will walk you through the procedure of removing the old accumulators and installing new ones in a W123 300TD wagon. It is a very straightforward job that only takes a couple hours. You will need to raise the car and safely support it on jack stands.
This video instruction will walk you through the step-by-step procedure of how to do a "service" on your power steering system.
PLEASE NOTE: UPS GROUND SHIPPING ONLY. Sorry, no postal, expedited or international shipping. This is a highly neglected maintenance item on older Mercedes Benz. If you want to prolong the life of your steering box and power steering pump here's how.
UPS GROUND SHIPPING ONLY. DO NOT order postal or expediated. International shipping not available. If your fluid is old and dark it is time to flush it out. 1986 to 1999 model W126, W201, W124, W140 and W126 with SLS have a smaller tank than the earlier models.
New O.E. filter as shown. See related products for fluid and flushing instructions. This is VERY easy to inspect and change yourself.
This instructional video covers the procedure for flushing the old hydraulic fluid out of an SLS system and installing new fluid. The example shown in this video is from a W126 560SEC.
Brand new rear end differential front seal. Fits both gas and diesel models. This is NOT the seal for the axles.
Brand new complete wheel bearing kit. Includes all parts shown for right or left wheel. You with need to order 2 if you want a complete set of wheel bearings for both sides.
New Bilstein rear touring shock absorber. Please check your vin number before ordering.
Brand new Genuine Mercedes leveling valve for self leveling suspension. If your suddenly loses its ability to adjust ride height or the ride becomes real mushy then this may be the culprit. One required per car. Current List Price is $ 505.00 USD.
Brand new high quality accumulator set for self leveling suspension SLS. If you suddenly have a harsh abrupt ride then this is usually the culprit. Two per car and should be replaced in pairs.
SLS low pressure hose from bottom of reservoir tank to the engine driven pump. Includes 1 meter of heavy duty fuel hose that holds up better to the hydraulic fuel than the old style original braided hose.
If you have any Mercedes model with hydraulic self leveling suspension from the early 70's up to the early 1990's this is the correct fluid to use. High quality Meyle or Febi Bilstein product. Any other type of fluid can damage the seals and score your pump.