All new 2006 to 2013 V6 and V8 engine repair kits! CLICK HERE to view AlL.
Kent's procedure uses the factory recommended "drip tube method" but with a "twist." He has devised a way to get accurate and consistant IP timing results while trying to get the drip tube to drip at one drip per second exactly when it should!
Any time you are removing and replacing your fuel injectors you will need to change the return hose and the heat shield crush washers. If you don’t, you will have leaking hoses and possible compression leaks at the injector nozzles.
This is the best way to determine if the expensive injection pump is going to work for old 4 AND 5-cylinder diesel engines that have not run in years. Watch the video below to understand what this kit can do.
This is every thing you need along with free video instructions by Kent Bergsma. Why change the K-jet fuel injectors in your M110 engine. One thing is they are very old. Second this is right now they are readily available and resonably inexpensive.
Did you hear these are not available? No part number anywhere? Well, as the source we went to work and made it happen. You can now purchase the correct copper sealing rings for your OM616 and OM617 injection pump delivery valves.
Those old hardened and discolored plastic fuel hoses in your diesel engine compartment probably need to be replaced. When they crack and break you can dump a ton of fuel out on the road before your engine quits and leaves you stranded.
This kit will give you everything you need to fix the leaking or aged Tee hose between the fuel damper and the fuel accumulator on most 1977 to 1980 fuel delivery systems. Watch the video below to learn why this is needed.
It was difficult to find a filter to fit the correct size outlet hose. Install this steel 10-micron filter in your fuel tank outlet hose to protect your fuel pump. Clamps are provided along with a pull to plug the fuel hose temporarily to reduce fuel spills.
This easy-to-install kit could do wonders for your older diesel engine. The lift pump is almost always forgotten when it comes to maintenance on the OM616 and OM617 engines.
This pump fits W116 300SD, W126 300SD, and the turbo W123 1981 to 1985. Removed for a low mileage (20K) facgtory remanufactured engine. New check valves and seals installed. A BRAND NEW hand primer pump is included. The gasket and supplies are included as shown in the picture.
This is a "must-have" kit when adjusting release "pop" pressures on older diesel mechanical fuel injectors. It is the internal spring "shim" thickness that determines the exact pressure required for the release of fuel at the tip of the injector.
If you acquire an older Mercedes diesel and want to test those large Bosch injectors with your V3 gasoline bench tester, you will need 4 things to complete the conversion: 3000 PSI gauge, our new capture bottle to hold the larger injectors, injector sealing kit, and Kent’s written manual and vid
We know that many of you own multiple Mercedes, including both gas and diesel models. If you own one of Kent’s fuel injector pressure testers you no doubt will want to test all your applicable mechanical fuel injectors in both types of older engines.
With these old gas fuel injectors, sometimes you just have to "back flush" the insides to restore them to peak performance. There is no guarantee that back flush cleaning will restore every old gasoline mechanical fuel injector. Some are just plain worn out.
This is something many owner's and mechanics miss. That little check valve on the side of the injection pump can cause a lot of starting problems on the older diesels.
The FLOW or low pressure method of checking and adjusting injection pump timing does not require a separate pressure tank. With this method you use the hand primer pump to pump up pressure in the injection pump to get fuel to flow out of the half round drip tube included in this kit.
We receive a large number of emails from customers complaining about small fuel leaks at the fuel injector housing (coming out the threads between the two halves)and how best to seal them. To fix this high pressure leak requires taking the injector apart and "lapping" the mating surfaces.
Fits 116, 123 and 126 chassis diesel 1977 to 1985 only, including the 240D 300D 300CD 300TD 300SD. This kit should give you at least a years supply of fuel filters for your diesel.
FITS THE FOLLOWING: 123, 240D, 300D, 300TD and 300CD from 1977 to 1985. The original fuel lines on most late 70s and early 80s Mercedes Diesels were braided line and with age they do rot and develop slow leaks.