Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
ONLY ONE LEFT. Good used activation rod and plastic clip as shown. Controls travel of vacuum control valve on the top rear of the injection pump. A plastic clip can easily break. May be some slight wear on the end of the metal rod but still usable.
Excellent used black plastic arm rest trim ring. has no breaks
Fits all 123 240D 300D 300CD 300TD 280E 280CE 1977 to 1985. This is a good used rear bumper rubber. There are no gouges or tears, only some slight scratches in places. The rubber trim piece that goes over the bumper shock mounts is in very good used condition.
DESCRIPTION: Excellent used combination turn signal, high beam and wiper switch assembly. Note no cruse control level included. Easy to install buy pulling wiring bundle right out through the steering column. There will be some wear on the handle.
This is a genuine Mercedes used part. These are much stronger than the aftermarket ones available. Genuine are no longer made. No damage to the slot or the threads. Only for models listed. Does not work on later aluminum diesel engines. Collar nut holds pre-chamber in cylinder head.
These two small o-rings seal the oil drain tube that goes from the bottom of the air filter into the engine oil pan.
8/2022 Update: We have modifed a new wrench for this kit so it may not look the same as that shown in previous YouTube videos, but it will do the same or even better job! We do sell the water pumps individually, but we decided to offer this complete kit to make a diesel pump installation go easie
For 1977 to 1985 240D 300D 300CD 300TD 280E 280CE. When I first saw these from our supplier I was really impressed with the quality. So I decided to put them one of my personal W123s that had faded and crazed Bosch originals. Watch the video below and I think you will be impressed too!
FITS: MERCEDES BENZ 190DT, MERCEDES BENZ 260E, MERCEDES BENZ 300CDT, MERCEDES BENZ 300CE, MERCEDES BENZ 300DT, MERCEDES BENZ 300E, MERCEDES BENZ 300SD, MERCEDES BENZ 300SDL, MERCEDES BENZ 300SE, MERCEDES BENZ 300SEL, MERCEDES BENZ 300SL, MERCEDES BENZ 300TD, MERCEDES BENZ 300TDT, MERCEDES BENZ 3
Good used plastic cover for glow relay as shown
PLEASE NOTE: We have been having problems recently obtaining these brackets. Turbo owner you may want to get a backup now before these are gone forever. If you order there could be a short shipping delay. Complete Kit as shown with installation tips included.
Good used turbo charger center section heat shield plate as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
Good used turbo charger center section to turbine housing hold down ring plate as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
Good used turbo charger exhaust manifold with good studs as shown. No other parts included. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer. This is the style that has the EGR outlet.
Good used turbo charger compressor housing as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
These large o-rings are used on the aluminum coupling that connects the turbo charger compressor outlet to the intake manifold. Should be changed with removing manifold or replacing turbo.
With this kit you will be able to hook up a pressure gauge to your intake manifold and route it inside your car for the purpose of monitoring your turbo charger boost pressure while driving.
When using a pencil glow plug reamer, this modified 12 mm wrench will allow you to PUSH in on the reamer while turning - and let me tell you - this is needed when you have heavy carbon buildup in the prechambers.
Three seals required to repair oil leaks in the straight oil drain tube going from the bottom of the turbo into the engine oil pan. This kit is intended for those who are rebuilding their turbo and have not changed these seals before.
High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.
I have been discovering this is one of those maintenance areas that suffers from severe neglect. Failure of the rubber support or center drive shaft bearing can cause all types of improperly diagnosed vibration problems - some commonly change with vehicle speed.
Set of (2). The number one cause of a loose or rattling shift lever is failed or missing shift lever bushings. Our upgraded bushings are made out of nylon and are much tougher than the original plastic type. No instructions or special tools included.
This is the most complete front reseal kit on the market today. It includes Kents new IMAGE-BY-IMAGE instructions. That means there is an image for every single step in the operation of replacing these 2 (Yes there are 2!) critical front seals.
Genuine MBZ Part with wiring plug for later models: Please note this buzzer is really for the 1985 and later models. The wiring pigtail is not used on pre-1985 steering locks. The switch itself is the same but for older models you will have to install and leave the pigtail connected.
Good used engine shock as shown. Fits right or left side.
Lower Engine Gasket and Seal Set as Shown. Contains many sizes of aluminum sealing washers. Please study picture carefully to see exactly what you are getting.
Brand new fog light bulb set as shown.
This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.
This sealing ring provides seal at the connection of the flexible down pipe and the exhaust pipe going back to the center muffler. This is an upgrade replacement for the older style crushable gasket seal. This all metal ring provides a much more reliable seal over time.
New inner front wheel bearing seal. Fits right or left side. Should be replaced when repacking wheels bearings with new grease. NOTE: DOES NOT work on cars with ABS brakes.
Until now there has been no practical information for the DIYer to know how to test and replace their own vacuum 3/2 valve assemblies. There certainly been no inexpensive hose replacement kits. This new kit by Kent Bergsma solves both those problems.
If you own a 123 wagon or other Mercedes with self-leveling suspension, you will be faced someday with having to replace the main high-pressure hydraulic hose that goes from the engine-driven pump to a metal line fitting routed back to the rear suspension.
New Genuine OEM rear stabilizer bar bushings, sold in a set of two. Fits 123 chassis 1977 to 1985 240D 300D 300TD 300CD 280E and 280CE.
Located above and aft of the rear differential as shown in picture below
We receive a large number of emails from customers complaining about small fuel leaks at the fuel injector housing (coming out the threads between the two halves)and how best to seal them. To fix this high pressure leak requires taking the injector apart and "lapping" the mating surfaces.
Includes 1 meter of nylon braided clear windshield washer hose. No instructions included.
CLICK HERE to view the complete windshield washer squirted kit.
10 red plastic clips are included as shown. There are a number of reasons why you would want to remove the center side trim on your older Mercedes. You may just want to clean and detail behind them (it does get pretty dirty back there over the years).
This GENUINE MERCEDES switch will work on all 107 chassis 380SL and 560SL 1981 to 1989, all 126 chassis sedans and coupes 1981 to 1991 , all 123 chassis 240D 300D 300CD 300TD from 1981 to 1985, all 201 chassis 190E 2.6 and 190D ( 190E 2.3 up to 1988 ONLY) and all 124 chassis from 1986 to 1993.
Get a spare. These will soon be NLA. NEW OLD STOCK Genuine Mercedes Ignition Switch. Fits early 123 chassis up through 1979, early 107 450SL from 1973-1980 and 1977-1980 116 300SD, 280SE, 450SE, and 450SEL.
Dont neglect this service as many do! I recommend the hydraulic fluid and filter be changed every 30,000 miles. You would not believe how many SLS vehicles I have seen with dirty hydraulic fluid - I mean nasty! Sometimes I have even found engine oil in the system!
I have never been impressed with the rubber vacuum hose found on older Mercedes diesels. I don't think the engineers ever anticipated how much abuse or how long these hoses would need to last!
GENUINE MERCEDES BENZ PART.
If it is taking a long time to get the windshield or headlight squirters to squirt this check valve may need replacing. Old valve nipples are easy to break off so if you are replacing the pump and hoses you may want a new valve on hand.
This rubber mount is often torn up, oil soaked or just plain missing. It sits right behind the center of the oil pan on a number of models listed above. I have often see the entire assembly removed. Check first to see if your engine has one before ordering.
Here are the correct size metric nuts with built in shoulder washer. If you drop these in behind the injection pump you may never find them. When doing glow plug service it is always a good idea to have some spare nuts on hand. New Bosch glow plugs do not come with new nuts.
This o-ring has to be tough enough to handle the high heat at the injection pump. If you see oil leaks around the area of the rack damper (located on bottom at rear of injection pump) then replace this o-ring.
Over the years I have used many different products to try to adhere chrome and trim pieces to body and interior panels. None has performed better for me than E6000. Silicone glue can't compete. When dry it holds like nothing else.
Application: Fits all 5 cylinder 116 and 126 Chassis diesel engines 300SD from 1978 to 1985 and all 123 Chassis 300D, 300CD and
Application: Applies to the model listed above. Excellent quality. They are Bosch Duraterm brand glow plugs.
Application: Fits all 116 and 126 Chassis 5 cylinder diesel engines 300SD from 1978 to 1985 and all 123 Chassis 300D, 300CD and 300TD from 1980 to 1985 with pencil glow plugs. Excellent quality. Five Bosch Duraterm pencil plugs with installation instructions.
Application: Fits all 123 chassis 4 cylinder 240D diesel engines from 1980 to 1983 with pencil glow plugs.
New nylon fan replacement. Only install on a fan clutch that originally had a nylon fan ( not an aluminum one). Shows up primarily on 1984 and 1985 models.