Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
I have been discovering this is one of those maintenance areas that suffers from severe neglect. Failure of the rubber support or center drive shaft bearing can cause all types of improperly diagnosed vibration problems - some commonly change with vehicle speed.
Set of (2). The number one cause of a loose or rattling shift lever is failed or missing shift lever bushings. Our upgraded bushings are made out of nylon and are much tougher than the original plastic type. No instructions or special tools included.
This is the most complete front reseal kit on the market today. It includes Kents new IMAGE-BY-IMAGE instructions. That means there is an image for every single step in the operation of replacing these 2 (Yes there are 2!) critical front seals.
This is referred to as the multifunction relay that controls, turn signal, hazard, wiper delay and rear window defroster. If you hare having problems with any of those check fuses first - then suspect relay.
Genuine MBZ Part with wiring plug for later models: Please note this buzzer is really for the 1985 and later models. The wiring pigtail is not used on pre-1985 steering locks. The switch itself is the same but for older models you will have to install and leave the pigtail connected.
Lower Engine Gasket and Seal Set as Shown. Contains many sizes of aluminum sealing washers. Please study picture carefully to see exactly what you are getting.
This is a high quality aftermarket part which I believe to be better than the original. And I have not been all that impressed with the original part. Then tend to fail way too often. You will need to remove the door panel to get to this unit. Video included in your account.
Brand new fog light bulb set as shown.
This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.
This sealing ring provides seal at the connection of the flexible down pipe and the exhaust pipe going back to the center muffler. This is an upgrade replacement for the older style crushable gasket seal. This all metal ring provides a much more reliable seal over time.
Brand new center drag link. Fits all 126 300SD 380SE/L 420SEL 500 from 1981 to 1991.
New inner front wheel bearing seal. Fits right or left side. Should be replaced when repacking wheels bearings with new grease. NOTE: DOES NOT work on cars with ABS brakes.
Until now there has been no practical information for the DIYer to know how to test and replace their own vacuum 3/2 valve assemblies. There certainly been no inexpensive hose replacement kits. This new kit by Kent Bergsma solves both those problems.
If you own a 123 wagon or other Mercedes with self-leveling suspension, you will be faced someday with having to replace the main high-pressure hydraulic hose that goes from the engine-driven pump to a metal line fitting routed back to the rear suspension.
New Genuine OEM rear stabilizer bar bushings, sold in a set of two. Fits 123 chassis 1977 to 1985 240D 300D 300TD 300CD 280E and 280CE.
Located above and aft of the rear differential as shown in picture below
We receive a large number of emails from customers complaining about small fuel leaks at the fuel injector housing (coming out the threads between the two halves)and how best to seal them. To fix this high pressure leak requires taking the injector apart and "lapping" the mating surfaces.
These are the plastic bushings that hold fuel injectors into the head of the late M116 and M117 engines. These get very brittle with age. If you are planning on removing your fuel injectors I highly recommend you order these to have on hand.
This is a critical rubber part that seals the fuel injector to the injector holder. Deterioration can result in high idle speeds and poor engine performance. Unless you have a low mileage car with soft seals, these should be changed when testing, cleaning, or replacing your fuel injectors.
We only have a few of these custom machined early 300SD steering locks left. LIMIT ONE per customer. We have been informed that there is no plan to manufacture new steering locks again for these classic old diesels
Includes 1 meter of nylon braided clear windshield washer hose. No instructions included.
CLICK HERE to view the complete windshield washer squirted kit.
10 red plastic clips are included as shown. There are a number of reasons why you would want to remove the center side trim on your older Mercedes. You may just want to clean and detail behind them (it does get pretty dirty back there over the years).
This GENUINE MERCEDES switch will work on all 107 chassis 380SL and 560SL 1981 to 1989, all 126 chassis sedans and coupes 1981 to 1991 , all 123 chassis 240D 300D 300CD 300TD from 1981 to 1985, all 201 chassis 190E 2.6 and 190D ( 190E 2.3 up to 1988 ONLY) and all 124 chassis from 1986 to 1993.
Get a spare. These will soon be NLA. NEW OLD STOCK Genuine Mercedes Ignition Switch. Fits early 123 chassis up through 1979, early 107 450SL from 1973-1980 and 1977-1980 116 300SD, 280SE, 450SE, and 450SEL.
If you need everything for your front hub bearing replacement then this is the best deal. This kit is for BOTH SIDES. Comes with inner and outer wheel bearings, seal, cap, AND ground clip. Fits models listed above only ( with ABS).
Dont neglect this service as many do! I recommend the hydraulic fluid and filter be changed every 30,000 miles. You would not believe how many SLS vehicles I have seen with dirty hydraulic fluid - I mean nasty! Sometimes I have even found engine oil in the system!
I have never been impressed with the rubber vacuum hose found on older Mercedes diesels. I don't think the engineers ever anticipated how much abuse or how long these hoses would need to last!
GENUINE MERCEDES BENZ PART.
If it is taking a long time to get the windshield or headlight squirters to squirt this check valve may need replacing. Old valve nipples are easy to break off so if you are replacing the pump and hoses you may want a new valve on hand.
This rubber mount is often torn up, oil soaked or just plain missing. It sits right behind the center of the oil pan on a number of models listed above. I have often see the entire assembly removed. Check first to see if your engine has one before ordering.
Glow plugs do not last forever. I have found they generally need to be replaced about every 2 years for peak performance.
Here are the correct size metric nuts with built in shoulder washer. If you drop these in behind the injection pump you may never find them. When doing glow plug service it is always a good idea to have some spare nuts on hand. New Bosch glow plugs do not come with new nuts.
This o-ring has to be tough enough to handle the high heat at the injection pump. If you see oil leaks around the area of the rack damper (located on bottom at rear of injection pump) then replace this o-ring.
Over the years I have used many different products to try to adhere chrome and trim pieces to body and interior panels. None has performed better for me than E6000. Silicone glue can't compete. When dry it holds like nothing else.
Application: Fits all 5 cylinder 116 and 126 Chassis diesel engines 300SD from 1978 to 1985 and all 123 Chassis 300D, 300CD and
Application: Applies to the model listed above. Excellent quality. They are Bosch Duraterm brand glow plugs.
Application: Fits all 116 and 126 Chassis 5 cylinder diesel engines 300SD from 1978 to 1985 and all 123 Chassis 300D, 300CD and 300TD from 1980 to 1985 with pencil glow plugs. Excellent quality. Five Bosch Duraterm pencil plugs with installation instructions.
Application: Fits all 123 chassis 4 cylinder 240D diesel engines from 1980 to 1983 with pencil glow plugs.
New nylon fan replacement. Only install on a fan clutch that originally had a nylon fan ( not an aluminum one). Shows up primarily on 1984 and 1985 models.
Some of those early fuel injections systems can be troublesome. If you don't understand the system or how it works you will never be able to troubleshoot it successfully. This manual explains the different comp0nents in the system, their purpose, and how they interact together.
Brand new Great locking gas cap with two new keys for these gas powered earlier models.
OEM style, made in Austria!
Best plugs for your 102 Engine. Yttrium electrodes out perform platinum especially if your engine is burning oil.
Brand new Meyle front Strut. Fits 190E 2.3 and 190D 2.2 and 190E 2.6
these years and models -- application notes:
Brand new front center drag link, made by Meyle. Fits all 201 chassis from 1984 to 1993. No instructions.
Fits all 190E 190D 300E 300CE Etc. from 1984 to 1993
Rebuilt 65 amp alternator without pulley or fan. You will need to install the fan and pulley from your existing alternator. The voltage regulator is included. No Core charge. No hassle trying to have to ship back your old one.
WILL NOT FIT 85 CALIFORNIA MODELS!! It will fit some 1985 Federal Models only.
Some of the most common auto transmission leaks on the early automatics come from the banjo bolts that connect the filler tube to the bottom of the pan and the two transmission coolers lines to the lower front transmission housing.
This is a very common failure item on the older gas models. The braided outlet fuel hose will rot and and begin by weeping fuel through the hose. When it finally fails it can be dangerous and leave you stranded on the road. Large amounts of fuel will come pouring out of the tank.
New Bosch fuel filter as shown. Before ordering please make certain that this fits your Benz. Not all gas fuel filters are created equal.
This check valve is mounted on the end of the electric fuel pump and prevents pressure from bleeding off after the engine has shut down. If you engine is slow to start after it has sat overnight that could be a sign the check valve needs replacement.
New 126 Chassis 300SD 380SE 560SEL 300SDL Febi Front Stabilizer Bar bushings. Sold in a Set of Two (2).