Search | W113

When Kent set out to find a good fender cover for his own use he and Kaia decided to make it available to our customers. Who doesn't like a good soft fender cover that stays in place? We know red shows the grease more than black but you have to admit these are a knockout!

Dirko sealing compound is permanently elastic, cold vulcanizing, silicone-rubber based. Can be used for connecting joints, cylinder head, crankcase, oil sump, timing case, thermostat, water pump, transmission, axles, differential, radiator, chassis.

Sil-Glyde is a silicone based brake lubricant recommended for the entire brake assembly and is compatible with rubber. It is moisture-proof and heat resistant to +600 degrees F, which means it won't burn-off like other brake noise products.

This is a must-have if you have a prized Benz or any car you don't drive often!! If you let any of your cars sit for long periods ( generally over 30 days) without driving them, you can ruin your battery, especially if you let it go completely dead.

Nice set of pick tools with plastic handles. They have strong steel tips which allow for more prying and twisting with less tendency to bend the tips as you would with dental pick tools. Note: Quarter is not included! Shown for size reference only

Brand new Genuine Part. Plastic ball sockets can deteriorate and threads can rust up. It is important you have a good operating rod and tight arm in order to properly adjust your rear end ride height. NO instructions included. See our manual on SLS troubleshooting for more information.

Grommets push into the holes in the trunk to hold the emblems for the right and left side as applicable. A must have if you plan to repaint your car. Video on how to remove your emblems without damaging them is included free. These will work on the following models.

Mercedes-Benz 230

If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.

This is one of Kent's favorite tools. Lets you reach into tight places - very long nose curved pliers with teeth - like hemostat. With the locking handles it is amazing what this clamp / pliers can hold - and the tight places it can get into!

WARNING:  IF YOU ORDER WRONG ONE BY MISTAKE THE PART IS NOT RETURNABLE!  Fits all models in chassis range listed below. PLEASE NOTE: This is a LEFT hand thread so you MUST check the thread pattern on your current tie rod before ordering in order to receive the correct part.

High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.

This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.

Brand new Great locking gas cap with two new keys for these gas powered earlier models.

OEM style, made in Austria!

Fits all 110 111 113 108 107 116 114 115 123 126 201 124 129 140 early 60's to late 90's

Another High Quality product from Lubro Moly. This is a 300ml can of Motor Oil Saver. It Rejuvenates rubber and plastic engine seals and reduces oil consumption via the piston rings and valve guides; counteracts the loss in viscosity of motor oils.

Another high quality product made by Lubro Moly. This is a 50g tube of Gear oil additive. It is a concentrated moly based treatment for manual shift transmissions, differentials, steering boxes, transaxles, and rear axles. Reduces Gear noise and whine, smooths shifting.

When replacing front brake discs on above chassis it is highly recommend you replace the bolts that hold the rotor to the bearing hub. Not needed on 201 124 or 129 chassis. Sold individually. 5 required per wheel.

New rubber stop for rear exhaust bracket. It plugs into the body right above the back of the rear muffler. Helps prevent rattle. Fits almost all models from late 1960s to mid 1990s. When you hear something clunking in the back when you go over a bump, this part is probably missing.

Buy a lemonhead for ten cents when added to any order including other item(s).

Limit 10 per customer

You asked for it so we made it happen. Many of you have been wanting to know what we use for high temp thread sealant (when we don't want to use the permanent epoxy). We don't like thread tape or anything with Teflon in it.