Fuel Pump Flange Gasket
Fits Mercedes Benz: 230 250 280 250S 280S 280C 220 250C
Kent's Factory Service Manuals collection is going on sale now. CLICK HERE.
Fits Mercedes Benz: 230 250 280 250S 280S 280C 220 250C
This set of 5 pick tools have very thin and sharp points. Best set Kent has found to remove orings in hard to get to locations. The variety of angles available allows you to get into almost anywhere to remove and o-ring, sealing ring or other small part.
If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.
This right angle screwdriver is great for working in tight places - like removing speakers, voltage regulators, distributor caps, etc.
This is one of Kent's favorite tools. Lets you reach into tight places - very long nose curved pliers with teeth - like hemostat. With the locking handles it is amazing what this clamp / pliers can hold - and the tight places it can get into!
January 2019 notice: This filter is now available only in very limited quantities and may not be readily available in the future. This is why we are not able to include it in our full fluid flush kit ( See related products below) This is an often neglected filter.
WARNING: IF YOU ORDER THE WRONG ONE IT IS NOT RETURNABLE.
I like the convenience of using the factory jack points (holes) but I absolutely DO NOT like using the factory jack - except in cases of emergency road side repair. You all know it can be a little unstable... I solved this problem by using a large heavy duty bolt.
SPECIAL ORDER PART -- MAY BE UP TO A WEEK BEFORE SHIPPING!
Plastic adjusting knob with clip. Fits many years and models with manually adusting mirrors.
High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.
Set of (2). The number one cause of a loose or rattling shift lever is failed or missing shift lever bushings. Our upgraded bushings are made out of nylon and are much tougher than the original plastic type. No instructions or special tools included.
Genuine MBZ Part with wiring plug for later models: Please note this buzzer is really for the 1985 and later models. The wiring pigtail is not used on pre-1985 steering locks. The switch itself is the same but for older models you will have to install and leave the pigtail connected.
This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.
10 red plastic clips are included as shown. There are a number of reasons why you would want to remove the center side trim on your older Mercedes. You may just want to clean and detail behind them (it does get pretty dirty back there over the years).
Over the years I have used many different products to try to adhere chrome and trim pieces to body and interior panels. None has performed better for me than E6000. Silicone glue can't compete. When dry it holds like nothing else.
Some of the most common auto transmission leaks on the early automatics come from the banjo bolts that connect the filler tube to the bottom of the pan and the two transmission coolers lines to the lower front transmission housing.
Fits all 110 111 113 108 107 116 114 115 123 126 201 124 129 140 early 60's to late 90's
WARNING: Can only ship inside the USA via UPS GROUND. If you have other items in your cart do not choose expedited shipping or US postal service! High Performance low moisture absorbing DOT brake fluid.
Another High Quality product from Lubro Moly. This is a 300ml can of Motor Oil Saver. It Rejuvenates rubber and plastic engine seals and reduces oil consumption via the piston rings and valve guides; counteracts the loss in viscosity of motor oils.
Another high quality product from Lubro Moly. This is a 90g tube of CV Joint grease for long term lubrication use. It is excellent for wheel bearings and ball joints as well.
Another high quality product made by Lubro Moly. This is a 50g tube of Gear oil additive. It is a concentrated moly based treatment for manual shift transmissions, differentials, steering boxes, transaxles, and rear axles. Reduces Gear noise and whine, smooths shifting.
If you have a leaking transmission seal it can be a real bear to get the old seals out without this puller tool. It works on both the front and rear transmission shaft seals. This tool also works great for removing the front crank seal on both gas and diesel engines.
This complete kit ncludes both inner and outer rear end wheel bearings and seals with groove nut and grease. Fits chassis listing above including the 123 300TD wagon, from 1974 to 1991. If you need bearings for both sides order 2 of these kits.
This is a maximum thickness rubber shim (19 mm thick) to adjust the ride height when installing new or reinstalling existing rear coil springs. Two required per car. Also fits 114, 115, 116, 123 sedans and coupes and 126 chassis cars.
This is a medium thickness rubber shim (14 mm thick) to adjust the ride height when installing new or reinstalling existing rear coil springs. Two required per car. Fits 116, 123 sedans, wagons and coupes and 126 chassis cars.
This item can only be shipped UPS Ground because it is a liquid. One Liter of correct Power steering fluid. Fully compatible with Dexron II systems but has enhanced aditives to reduce steering box gear wear.
For all 111, 112, 108, 109, 114, 115, 107, 116, 123, 126 and 201 chassis (Non tilting roofs up through 1986). Do you have a power sunroof that is working poorly or maybe not at all? Does it move slowly or not at all in the morning, but when it heats up during the day it works just fine?
When replacing front brake discs on above chassis it is highly recommend you replace the bolts that hold the rotor to the bearing hub. Not needed on 201 124 or 129 chassis. Sold individually. 5 required per wheel.
Brand new Auto transmission torque converter drain plug for All Mercedes, gasoline and diesel, from the late 60s up to the late 90s. If you are doing a complete transmission flush you will need to drain the torque converter. Good to have spare on hand!
New rubber stop for rear exhaust bracket. It plugs into the body right above the back of the rear muffler. Helps prevent rattle. Fits almost all models from late 1960s to mid 1990s. When you hear something clunking in the back when you go over a bump, this part is probably missing.
GENUINE MERCEDES BENZ PART.
Brand new factory type braided cloth injector end plug for all diesels 220D 240D 300D 300CD 300TD 300SD 300SDL E300D, from 1968 to 1995. Sold individually. Check yours for cracks or leaking! Very important that the end plug be in good condition or fuel leaks will occur.
Buy a lemonhead for ten cents when added to any order including other item(s).
Limit 10 per customer
Good, used, straight, older aluminum factory wheel. Above average condition. No corrosion or major curb lip damage. No gouges. No bolts or center cap included. This is the narrow wheel for smaller-bodied Mercedes 14 x 6 inches. Not for the S and SL classes.
Front flexible brake hose fits right or left side of most models from 1967 to 1985 including 250SE 280SE 300SEL 250 280 220D 240D 300D 450SE 300SD. Does NOT work on 123 chassis cars.
You asked for it so we made it happen. Many of you have been wanting to know what we use for high temp thread sealant (when we don't want to use the permanent epoxy). We don't like thread tape or anything with Teflon in it.
Fits 107 115 116 123 and 126 Chassis. This "must have" kit will help you replace the rubber flexible brake hoses on your older Mercedes from the late 60s up through the late 80s.
Brand new semi metallic aftermarket Front brake pad set. Both right and left SIDE. Low dust formula. You will love how these pads seat in and feel - and especially how they don't squeal.... These fit a large number of models including 230 200D 250SL, 280SL, 250S, 250SE, 280S, 280SE.
We recommend you always replace this seal when removing and replacing your rear axles. You will need two of these if you are working on both axles. Seal fits on either side of the rear differential that uses can style rear axles. They will fit rear ends with ONLY can-style axles.
This small rubber cap protects dirt from entering your level indicator on your brake fluid reservoir. Fits 107 114 115 116 123 126 201 and 124 models from the early 70s to mid 1990s.
This large size rubber grommet seal is a common leak area at the bottom of your brake fluid reservoir. Fits all 107 chassis, 114 and 115 chassis SEDANS ONLY, 116 chassis and 123 chassis from 1972 to 1985.
This kit will include the parts and detailed PDF instructions you will need to repair a front transmission case leak in your 1968 to 1983 NON TURBO diesel automatic.
Applies to 111 113 108 109 107 114 116 126 Chassis Mercedes.
PLEASE NOTE: This item can ONLY be shipped UPS Ground. Diesel purge is amazing stuff! It is getting so popular that we have decided to offer it on the website individually, so now you can buy per can.
These same clips are used on almost all Mercedes Benz Models from the late 1960s up into the 1990s. If you have lost or damaged one of your clips here is a chance to get replacements. Maybe good idea to have spares on hand. Sold in set of 2.
Brand new Genuine OEM silver wheel center cap. Make those wheels look beautiful again! Fits all 14 inch alloys on 107 116 114 115 123 and 126 chassis to 1985 with the bundtcake style wheels.
In working on many 61x series diesel engines, I have often found one or more of these clamps missing. Missing or loose clamps are the number one reason for injector hardline crack failure. There should be a clamp like this between every two hard lines to minimize vibration fatigue failure.
Good used emergency brake shoe adjuster star nut and pin. Fits all models from chassis in title.