In this 14-minute video instruction, you will get to see how Kent cleans and details an engine compartment in a W210 E430 using his favorite chemicals and techniques. This includes using less than a gallon of water and controlling the spray rinse so you protect sensitive electrical components.
Search | W126 | Engine
New crank main rear seal
This kit contains the following matched fittings. Two brass connector fittings and two hose clamps are included to help you fix old leaking air hoses. One is for 5/16 inch hose and the other brass fitting is for 3/8 inch air hose.
New quality metal gasket as shown. Never try to reuse this gasket during turbo overhaul or replacement.
Brand new part. No instructions included. See related products below. Instructions do come with our turbo timing chain kit.
Brand new quality part. No instructions included. Instructions do come with our timing chain kit.
Brand new Febi Bilstein part. WARNING: Must be installed properly or damage can occur to the timing chain and sprockets. Kent always recommends you replace the tensioner when you install a new timing chain. NO INSTRUCTIONS. Instructions do not come with this part.
When cleaning and cosmetically restoring your cars engine and engine compartment, you will need containers for the various cleaners, acids, paints and sealants you might use as well as brushes to apply them.
Kent has been working a long time to find a way to stop the ugly corrosion on aluminum and magnesium engine parts. Particularly valve covers and intake manifolds. Help Kent out here to test this new product he has been using. The kit includes a 1 oz container of gel and a scotch brite pad.
If you are tired of "guessing" on those critical low torque settings maybe it is time to get a small torque wrench. This is the one Kent likes for super low torque settings up. It is quality made and will not cost you an arm and a leg. You can even calibrate it yourself!
Too many emails on this subject pretty much forced Kent to do this almost 3 hour long video class. If you are having problem starting your old 1976 to 1993 Mercedes with Bosch C.I.S. fuel injection this is a must see.
When prepping many surfaces on your engine for replacement gaskets or application of RTV sealant it is very important not to scratch the metal. In some cases that can set up corrosion or possible small leaks that will lead to premature failure of the repair.
Kent uses these superb plastic razor blades regularly in his shop. Recently they proved very useful when resealing the magnesium engine breather covers on an M113 engine. There are seven green and three orange in this little package.
Guide use pin for upper guide rail at the top of the cylinder head. These often get striped out trying to remove them.
This is one of Kent's favorite tools around his shop. It is used almost daily. The tool rose out of a need to be able to safely hold fuel inectors while cleaning when with a large high speed wire wheel. No tool like this is availabe so it had to be built in our shop!
This is the highly specialized paper gasket that seals the center section forward bearing plate to the compressor wheel housing as shown below:
This video will be an excellent example of how to save big $$$ doing the work on your own car. If your gas engine is idling too fast in neutral it could be an expensive problem, but in many cases it is due to lack of maintenance over a long period of time.
If you have a Mercedes of this era equipped with an impulse code reader you will find a little numbered black box similar to the one in the pictured here in your engine compartment. It is located over by the battery and may have a black cover on it that can be lifted off.
Kent starts out the video talking about prevention by using the neck reinforcement kit he has been selling for years. In the case of his own 1990 300SL the neck had not been reinforced and it broke cleanly right in the middle.
Distributor neglect is one of the most common neglected maintenance items that we see on the 6 cylinder 103 engine. Just because the engine is running ok does not mean that the parts are not worn out. One day you will get up in the morning and the engine will not start.
This is a must have if you own an older turbo 300D 300TD 300CD or 300SD. Full of very valuable info. No longer in print and hard to find. This is the factory dealer workshop full engine service manual.
Good used oil drain pipe as shown with good bracket attach point. For 1981 to 1984 Turbo 300TD 300D 300CD and 300SD.
This is the standard 14 mm long pan plug used on many engines with aluminum pans from the mid 1980's on. Before ordering make certain you have this type of pan plug. This engine oil drain plug can help extend the life of your old diesel engine.
Want to find out what caused the catastrophic destruction of an OM 617 5 Cylinder turbo diesel engine? These engines are known for being indestructable so something really bad had to happen.
All kinds of metric bolts and engine related as shown. Study the picture carefully. This is exactly what you will receive.
Good used straight power steering pump pulley. Fits only those models listed turbo 300D 300CD 300TD and 300SD
Parts as shown. For US model power steering pumps 240D, 300D, 300TD, 300CD and 300SD 1981 to 1985.
Good used tank and hoses as shown. This is the original style tank that is no longer available ( without the hole for the level sensor). So this only works on the early W126 sedan diesels. Includes non original cap.
Good used thermostat housing as shown. This is the section that bolts onto the side of the cylinder head. Not heavily corroded like most. Will clean up real nice. Both sensors are included inside but cannot guarantee they will work properly as they have not been tested.
ONLY ONE AVAILABLE. Very good used OE air filter housing bracket. Comes with three good recently new rubber mounts and metal heat shields ( not shown in this picture). Fits 1978 to 1984 300SD, 1981 to 1984 300TD and 1982 to 1984 300D and 300CD.
Very good used aluminum power steering pump for your 4 and 5 cylinder diesel engine. Only fits years listed. Comes with cap, wing nut and internal spring. No filter. Recommend a new filter (not included) and upgrade to better power steering fluid ( not auto trans fluid!)
Good used later OM671 turbo intake elbow. For 1981 to 1984 models without trap oxidizer. Please note comes with both clamps and older but straight rubber seals. Seals are usable but just starting to get a little hard.
Excellent air filter assembly housing with short tube design. No cracks, good cap stud and threads,and all side clips intact. No dent damage. Does not include wing nut. No air filter included. PLEASE NOTE: This filter does NOT include the hose attached to the side in the picture.
This upper guide rail is no longer available new. If yours is cracked or excessively worn then it needs to be changed when you replace a timing chain. We have collected all the good ones we have which are not very many.
When working on automotive engines a long heavy machinist straight edge is a must. This is the best way to tell if the mating surfaces are flat and true. That includes cylinder heads, engine blocks, intake and exhaust manifolds as well as critical sealing metal to metal covers and housings.
A properly functioning and adjusted waste gate is critical to the proper operation of your early turbo charged Mercedes diesel engine.
Pencil (parallel style) glow plugs usually fail slowly over time. The first signs are rough running after startup. Then you may see a flashing glow plug light on your dash. If ignored over time you engine may not start at all.
Excellent used turbo diesel oil cooler. Only fits models listed. Excellent threads on fittings and no leaks.
Many owners neglect replacing the engine coolant thermostat. It just slowly wears out over time. If you notice your engine temperature running low or you car taking a long time to heat up inside these are the first signs your thermostat has failed.
No expedited shipping. Please allow 3 to 5 business days before this part can be shipped. It is not located at our main shipping warehouse and sometimes it will need to be removed from a car before it can be cleaned and packed for shipping. Thanks for your understanding.
This standard 24 mm combination wrench is specially ground in our shop so that it will hold the fitting on the late 616 and 617 oil filter housing when loosening the oil cooler hose end nut. Without this wrench the fitting may start to turn with the hose nut and you will never get it off.
This kit will allow you to replace the critical worn parts inside the early 603 U.S. made Garrett T3 turbochargers. This kit will not work if your engine has a KKK turbo made in Germany. The only way to tell which turbo you have is by visual inspection.
No expedited shipping. Please allow 3 to 5 business days before this part can be shipped. It is not located at our main shipping warehouse and sometimes it will need to be removed from a car before it can be cleaned and packed for shipping.